- 您现在的位置：买卖IC网 > PDF目录2007 > MAX1011CEG+ (Maxim Integrated Products)IC ADC 6BIT 90MSPS 24-QSOP PDF资料下载
参数资料
| 型号： | MAX1011CEG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 6BIT 90MSPS 24-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 位数： | 6 |
| 采样率（每秒）： | 90M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 215mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；2 个差分，单极 |
MAX1011
External Clock Operation
To accommodate designs that use an external clock,
the MAX1011’s internal oscillator can be overdriven by
an external clock source (Figure 7). The external clock
source should be a sinusoid to minimize clock phase
noise and jitter, which can degrade the ADC’s ENOB
performance. AC couple the clock source (recom-
mended voltage level is approximately 1Vp-p) to the
oscillator inputs (Figure 7).
Output Data Format
The conversion results are output on a 6-bit-wide data
bus. Data is latched into the ADC output latch following
a pipeline delay of one clock cycle (Figure 8). Output
data is clocked out of the ADC’s data output pins (D0
through D5) on the rising edge of the clock output
(DCLK), with a DCLK-to-data propagation delay (tPD) of
3.0ns. The MAX1011 outputs are +3.3V CMOS-logic
compatible.
Transfer Function
Figure 9 shows the MAX1011’s nominal transfer function.
Output coding is offset binary with 1LSB = FSR / 63.
___________Applications Information
The MAX1011 is designed with separate analog and
digital power-supply and ground connections to isolate
high-current digital noise spikes from the more sensi-
tive analog circuitry. The high-current digital output
ground (OGND) and analog ground (GND) should be
at the same DC level, connected at only one location
on the board. This will provide best noise immunity and
improved conversion accuracy. Use of separate
ground planes is strongly recommended.
The entire board needs good DC bypassing for both
analog and digital supplies. Place the power-supply
bypass capacitors close to where the power is routed
onto the board, i.e., close to the connector. 10F elec-
trolytic capacitors with low-ESR ratings are recom-
mended. For best effective bits performance, minimize
capacitive loading at the digital outputs. Keep the digi-
tal output traces as short as possible.
The MAX1011 requires a +5V ±5% power supply for
the analog supply (VCC) and a +3.3V ±300mV power
supply connected to VCCO for the logic outputs.
Bypass each of the VCC supply pins to its respective
GND with high-quality ceramic capacitors located as
close to the package as possible (Table 2). Consult the
evaluation kit manual for a suggested layout and
bypassing scheme.
Low-Power, 90Msps, 6-Bit ADC
8
_______________________________________________________________________________________
Figure 7. External Clock Drive Circuit
MAX1011
CLK
DRIVER
TNK-
VCLK
VCLK = 300mVp-p TO 1.25Vp-p
TNK+
50
50
Z0 = 50
50
0.1
F
0.1
F
0.01F
Oscillator/Clock
47pF
Digital Output
9
16
13
BYPASS
TO GND/
OGND
(PIN)
10
6
17
0.01F
Converter
14
VCC/
VCCO
(PIN)
11
SUPPLY
FUNCTION
0.01F
Analog Inputs
CAPACITOR
VALUE
Table 2. Bypassing Guide
Figure 6. Tank Resonator Oscillator
MAX1011
CLK
DRIVER
VARACTOR DIODE PAIR IS M/A-COM MA4ST079CK-287
(SOT23 PACKAGE)
INDUCTOR COILCRAFT 1008HS-221.
VTUNE = 0V TO 8V
fOSC = 70MHz TO 109MHz
TNK-
TNK+
VTUNE
220nH
5pF
47pF
47k
10k
相关PDF资料 |
PDF描述 |
|---|---|
| MAX105ECS+T | IC ADC 6BIT 800MSPS DL 80TQFP |
| MAX1063AEEG+ | IC ADC 10BIT 250KSPS 24-QSOP |
| MAX107ECS+ | IC ADC 6BIT 400MSPS DL 80-TQFP |
| MAX1080AEUP+ | IC ADC 10BIT 400KSPS 20-TSSOP |
| MAX1084AESA+ | IC ADC 10BIT 400KSPS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1011CEG+ | 功能描述:模数转换器 - ADC Low-Power 90Msps 6-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1011CEG+T | 功能描述:模数转换器 - ADC Low-Power 90Msps 6-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1011CEG-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1011EVKIT | 功能描述:数据转换 IC 开发工具 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX101A | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:500Msps, 8-Bit ADC with Track/Hold |
发布紧急采购，3分钟左右您将得到回复。