- 您现在的位置：买卖IC网 > PDF目录9467 > MAX1022BETX+T (Maxim Integrated Products)IC ADC/DAC 10BIT W/FIFO 36-TQFN PDF资料下载
参数资料
| 型号： | MAX1022BETX+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/44页 |
| 文件大小： | 0K |
| 描述： | IC ADC/DAC 10BIT W/FIFO 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | ADC，DAC |
| 分辨率（位）： | 10 b |
| 采样率（每秒）： | 225k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MAX1020/MAX1022/MAX1057/MAX1058
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
21
Unipolar or Bipolar Conversions
Address the unipolar- and bipolar-mode registers
through the setup register (bits 1 and 0). See Table 5 for
the setup register. See Figures 3 and 4 for the transfer-
function graphs. Program a pair of analog inputs for dif-
ferential operation by writing a one to the appropriate bit
of the bipolar- or unipolar-mode register. Unipolar mode
sets the differential input range from 0 to VREF1. A nega-
tive differential analog input in unipolar mode causes the
digital output code to be zero. Selecting bipolar mode
sets the differential input range to ±VREF1 / 2. The digital
output code is binary in unipolar mode and two’s com-
plement in bipolar mode.
In single-ended mode, the MAX1020/MAX1022/
MAX1057/MAX1058 always operate in unipolar mode.
The analog inputs are internally referenced to AGND
with a full-scale input range from 0 to the selected refer-
ence voltage.
Analog Input (T/H)
The equivalent circuit of Figure 2 shows the ADC input
architecture of the MAX1020/MAX1022/MAX1057/
MAX1058. In track mode, a positive input capacitor is
connected to AIN0–AIN15 in single-ended mode and
AIN0, AIN2, and AIN4–AIN14 (only positive inputs) in
differential mode. A negative input capacitor is con-
nected to AGND in single-ended mode or AIN1, AIN3,
and AIN5–AIN15 (only negative inputs) in differential
mode. For external T/H timing, use clock mode 01. After
the T/H enters hold mode, the difference between the
sampled positive and negative input voltages is con-
verted. The input capacitance charging rate determines
the time required for the T/H to acquire an input signal.
If the input signal’s source impedance is high, the
required acquisition time lengthens.
Any source impedance below 300
does not signifi-
cantly affect the ADC’s AC performance. A high-imped-
ance source can be accommodated either by
lengthening tACQ (only in clock mode 01) or by placing
a 1F capacitor between the positive and negative ana-
log inputs. The combination of the analog-input source
impedance and the capacitance at the analog input cre-
ates an RC filter that limits the analog input bandwidth.
Input Bandwidth
The ADC’s input-tracking circuitry has a 1MHz small-
signal bandwidth, making it is possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. Anti-alias prefiltering
of the input signals is necessary to avoid high-frequen-
cy signals aliasing into the frequency band of interest.
Analog-Input Protection
Internal electrostatic-discharge (ESD) protection diodes
clamp all analog inputs to AVDD and AGND, allowing
the inputs to swing from (VAGND - 0.3V) to (VAVDD +
0.3V) without damage. However, for accurate conver-
sions near full scale, the inputs must not exceed VAVDD
by more than 50mV or be lower than AGND by 50mV. If
an analog input voltage exceeds the supplies, limit the
input current to 2mA.
Internal FIFO
The MAX1020/MAX1022/MAX1057/MAX1058 contain a
first-in/first-out (FIFO) buffer that holds up to 16 ADC
results plus one temperature result. The internal FIFO
allows the ADC to process and store multiple internally
clocked conversions and a temperature measurement
without being serviced by the serial bus.
If the FIFO is filled and further conversions are request-
ed without reading from the FIFO, the oldest ADC
results are overwritten by the new ADC results. Each
result contains 2 bytes, with the MSB preceded by four
leading zeros and the LSB followed by 2 sub-bits. After
each falling edge of
CS, the oldest available pair of
bytes of data is available at DOUT, MSB first. When the
FIFO is empty, DOUT is zero.
AIN0–AIN15
(SINGLE-ENDED),
AIN0, AIN2,
AIN4–AIN14
(DIFFERENTIAL)
COMPARATOR
HOLD
ACQ
HOLD
ACQ
HOLD
AVDD/2
REF1
AGND
CIN+
CIN-
DAC
AGND
(SINGLE-ENDED),
AIN1, AIN3,
AIN5–AIN15
(DIFFERENTIAL)
Figure 2. Equivalent Input Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MS27505E17F6P | CONN RCPT 6POS BOX MNT W/PINS |
| MAX186DCAP+T | IC ADC 12BIT SERIAL 20-SSOP |
| MS27474T14B37SB | CONN RCPT 37POS JAM NUT W/SCKT |
| MAX188CCAP+T | IC ADC 12BIT SERIAL 20-SSOP |
| MAX192BEAP+T | IC ADC 10BIT SERIAL 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1023 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1023BETX | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1026 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1026_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1026_11 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
发布紧急采购，3分钟左右您将得到回复。