- 您现在的位置：买卖IC网 > PDF目录2085 > MAX1035EUP+T (Maxim Integrated Products)IC ADC 14BIT SER 115KSPS 20TSSOP PDF资料下载
参数资料
| 型号： | MAX1035EUP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/31页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SER 115KSPS 20TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 14 |
| 采样率（每秒）： | 115k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 879mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX1034/MAX1035
8-/4-Channel, ±VREF Multirange Inputs,
Serial 14-Bit ADCs
24
______________________________________________________________________________________
M2
M1
M0
MODE
0
External Clock (DEFAULT)
0
1
External Acquisition
0
1
0
Internal Clock
0
1
Reserved
1
0
Reset
1
0
1
Reserved
1
0
Partial Power-Down
1
Full Power-Down
Table 8. Mode-Control Bits M[2:0]
For the external acquisition mode, CS must remain low
for the first 15 clock cycles and then rise on or after the
falling edge of the 16th clock cycle as shown in Figure 3.
For optimal performance, idle DIN and SCLK during the
conversion. With careful board layout, transitions at DIN
and SCLK during the conversion have a minimal impact
on the conversion result.
After the conversion is complete, SSTRB asserts high
and CS can be brought low to read the conversion
result. SSTRB returns low on the rising SCLK edge of
the subsequent start bit.
Internal Clock Mode (Mode 2)
In internal clock mode, the internal clock controls both
acquisition and conversion of the analog signal. The inter-
nal clock starts approximately 100ns to 400ns after the
falling edge of the eighth SCLK and has a rate of about
4.5MHz. The analog input sampling instant occurs at the
falling edge of the 11th internal clock signal (Figure 4).
For the internal clock mode, CS must remain low for the
first seven SCLK cycles and then rise on or after the
falling edge of the eighth SCLK cycle. After the conver-
sion is complete, SSTRB asserts high and CS can be
brought low to read the conversion result. SSTRB returns
low on the rising SCLK edge of the subsequent start bit.
Reset (Mode 4)
As shown in Table 8, set M[2:0] = 100 to reset the
MAX1034/MAX1035 to its default conditions. The
default conditions are full power operation with each
channel configured for ±VREF, bipolar, single-ended
conversions using external clock mode (mode 0).
Partial Power-Down Mode (Mode 6)
As shown in Table 8, when M[2:0] = 110, the device
enters partial power-down mode. In partial power-
down, all analog portions of the device are powered
down except for the reference voltage generator and
bias supplies.
To exit partial power-down, change the mode by issu-
ing one of the following mode-control bytes (see the
Mode Control section):
External-Clock-Mode Control Byte
External-Acquisition-Mode Control Byte
Internal-Clock-Mode Control Byte
Reset Byte
Full Power-Down-Mode Control Byte
This prevents the MAX1034/MAX1035 from inadvertent-
ly exiting partial power-down mode because of a CS
glitch in a noisy digital environment.
Full Power-Down Mode (Mode 7)
When M[2:0] = 111, the device enters full power-down
mode and the total supply current falls to 1A (typ). In
full power-down, all analog portions of the device are
powered down. When using the internal reference,
upon exiting full power-down mode, allow 10ms for the
internal reference voltage to stabilize prior to initiating a
conversion.
To exit full power-down, change the mode by issuing
one of the following mode-control bytes (see the
Mode
Control section):
External-Clock-Mode Control Byte
External-Acquisition-Mode Control Byte
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1036LEKA+T | IC ADC 8BIT LP SERIAL SOT23-8 |
| MAX1060AEEI+ | IC ADC 10BIT 400KSPS 28-QSOP |
| MAX1062AEUB+ | IC ADC 14BIT 200KSPS 10-UMAX |
| MAX1066BEUP+ | IC ADC 14BIT 165KSPS 20TSSOP |
| MAX1067BCEE+ | IC ADC 14-BIT 200KSPS 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1036 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036EKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX1036EKA- | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2.7V to 5.5V, Low-Power, 4-/12-Channel 2-Wire Serial 8-Bit ADCs |
| MAX1036EKA+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 188KSPS 8BIT SERL 8PIN SOT-23 - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC 8BIT ADC 2WIRE SERIAL SOT8 |
发布紧急采购，3分钟左右您将得到回复。