- 您现在的位置：买卖IC网 > PDF目录17007 > MAX11040DBEVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX11040 PDF资料下载
参数资料
| 型号： | MAX11040DBEVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/31页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MAX11040 |
| 产品培训模块： | MAX11200 ADC Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 软件下载： | MAX11040EVKIT |
| 标准包装： | 1 |
| ADC 的数量： | 4 |
| 位数： | 24 |
| 采样率（每秒）： | 64k |
| 数据接口： | SPI?、QSPI?、MICROWIRE? 和 DSP |
| 输入范围： | ±2.2 V |
| 工作温度： | -40°C ~ 105°C |
| 已用 IC / 零件： | MAX11040 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX11040 Evaluation Kit/Daughterboard
Cascade
Carefully connect the boards by aligning the EV kit’s
14-pin connector (J12) with the 14-pin header (J1) of
the daughterboard. Gently press them together. The
two boards should be flush against each other. If more
daughterboards need to be cascaded to the EV kit,
connect the 14-pin connector (J2) of the last daughter-
board with the 14-pin header (J1) of the additional
daughterboard.
Place the shunt on pins 2-3 of JU3 on the last daughter-
board (the one farthest away from the EV kit board),
and place the shunt on pins 1-2 of JU3 on all other
boards (including the EV kit board).
Power Supply
Two separate power supplies are required to power up
the daughterboard. Connect the analog voltage supply
(from +3V to +3.6V) and the analog ground to the
Table 2. Jumper Settings (Daughterboard)
AVDD and AGND connectors, respectively. Connect
the digital voltage supply (from +2.7V to AVDD) and the
digital ground to the DVDD and DGND connectors on
the daughterboard, respectively.
LEDs
There are four LED indicators (D1–D4) on the daughter-
board. D1 and D2 LEDs reflect the real-time logic levels
on the FAULT and the OVRFLW pins, respectively. D3
and D4 LEDs latch on the fault conditions on the FAULT
and the OVRFLW pins, respectively. When D3 or D4 is
turned on, press the Clear LED button in the EV kit soft-
ware (Figure 1) or press the on-board pushbutton (S2)
to turn off the LEDs after the faults are cleared. All IC
FAULT and OVERFLW pins are open drain and respec-
tively connected in a wired-ORed configuration.
JUMPER
JU1
JU2
JU3
JU4
SHUNT
POSITION
1-2
Open*
1-2
Open*
1-2
2-3*
1-2*
2-3
DESCRIPTION
Connects the on-board crystal (Y1) to the crystal
oscillator input and output of the IC (U1)
Disconnects the on-board crystal from the IC
(U1)
Connects the XOUT pin of the IC (U1) to the
EX_XOUT pad
Disconnects the EX_XOUT pad from the XOUT
pin of the IC (U1)
Connects the DRDYOUT pin of the IC (U1) to the
CO_DRDYOUT pin on the connector (J2)
Connects the DRDYOUT pin of the IC (U1) to the
interrupt pin (INT0) of the on-board controller
Connects the XIN pin of the IC (U1) to the CI_XIN
pin on the J1 connector
Note: CI_XIN carries the CLKOUT signal from the
previous cascaded board
Connects the XIN pin of the IC (U1) to the
EX_XIN pad
Note: User-supplied external crystal may be
connected to the IC (U1) through the EX_XIN and
WHEN TO USE THIS OPTION
When the user wishes to stimulate the IC
modulator clock by the on-board crystal (Y1)
When the user does not wish to stimulate the IC
(U1) modulator clock by the on-board crystal
(Y1)
When the user-supplied external crystal
connects to the IC (U1) through the EX_XIN and
the EX_XOUT pads
When an external crystal is not used
Use this option when more IC daughterboards
need to be cascaded
Use this option on the last IC daughterboard that
cascades to the IC EV kit
When the user wishes to stimulate the IC (U1)
modulator clock by the CLKOUT of the previous
cascaded board
When the user does not wish to stimulate the IC
(U1) modulator clock by the CLKOUT of the
previous cascaded board
the EX_XOUT pads
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1231BEVKIT# | KIT EVALUATION FOR 12BIT ADCS |
| SDR1105-470KL | INDUCTOR POWER 47UH 10% SMD |
| GSM11DSEH-S13 | CONN EDGECARD 22POS .156 EXTEND |
| 101-0437 | CARD DGTL IO 16/8 SOURCNG SR9205 |
| 0210490250 | CABLE JUMPER 1.25MM .229M 18POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11040DBEVKIT+ | 功能描述:子卡和OEM板 MAX11040DB Eval Kit RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MAX11040EVKIT+ | 功能描述:数据转换 IC 开发工具 MAX11040DB Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX11040GUU/GH9 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX11040GUU+ | 功能描述:模数转换器 - ADC 24Bit 4Ch Simul-Samp Cascadable Sig Delt RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX11040GUU+T | 功能描述:模数转换器 - ADC 24Bit 4Ch Simul-Samp Cascadable Sig Delt RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。