参数资料
型号: MAX11060GUU+T
厂商: Maxim Integrated Products
文件页数: 7/35页
文件大小: 0K
描述: IC ADC 16BIT DELTA SIGMA 38TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
位数: 16
采样率(每秒): 3.07M
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 4
功率耗散(最大): 1.1W
电压电源: 模拟和数字
工作温度: -40°C ~ 106°C
安装类型: 表面贴装
封装/外壳: 38-TFSOP(0.173",4.40mm 宽)
供应商设备封装: 38-TSSOP
包装: 带卷 (TR)
输入数目和类型: 8 个单端,双极;4 个差分,双极
MAX11040K/MAX11060
24-/16-Bit, 4-Channel, Simultaneous-Sampling,
Cascadable, Sigma-Delta ADCs
15
Maxim Integrated
When the analog input voltage changes between the
ADC full scale and the fault threshold faster than the
latency of the converter, OVRFLW goes low with the
FAULT output. OVRFLW remains invalid until a valid
clock frequency is available at XIN.
Overvoltage-Fault Detection and Recovery (
FAULT)
With overvoltage-fault protection enabled (FAULTDIS =
0), FAULT immediately transitions from a high to low
when any of the analog inputs go outside the voltage
range bounded by the fault-detection thresholds VPFT
and VNFT.
Once the analog inputs return back within the fault
thresholds, the FAULT interrupt output goes high after a
delay called the fault-recovery time. The fault-recovery
time is:
20 x tDOUT < fault-recovery time < 25 x tDOUT
where tDOUT is the data output period determined by
fXINCLOCK and the selected output data rate.
In the event the analog input voltage changes between
the ADC full scale and the fault threshold faster than
the latency of the converter, the ADC conversion result
prematurely jumps to the full-scale value when a fault is
detected (see Detection Discontinuity in Figure 4).
During a fault condition and the subsequent fault-
recovery time, the ADC conversion result remains at full
scale. This creates a discontinuity in the digital conver-
sion result only if the fault recovery time is greater than
the latency plus the time that the input changes
between the fault threshold and the ADC full scale (see
Recovery Discontinuity in Figure 4). Neither of these
steps occur if the fault-protection circuitry is disabled
(FAULTDIS = 1), or if the input is slow relative to the
above descriptions (see Figure 5).
For data rates faster than 32ksps (FSAMPC = 111), the
converter output may contain invalid data for up to
188μs after FAULT returns high. To prevent this behav-
ior, disable the overvoltage-fault protection by setting
the FAULTDIS bit in the configuration register to 1 when
using FSAMPC = 111, and limit the analog input swing
to ±3.5V.
|AIN+ - AIN-|
LATENCY
DETECTION
DISCONTINUITY
RECOVERY
DISCONTINUITY
FULL SCALE
(|0.88VREF|)
FAULT-DETECTION
THRESHOLD
(VPFT OR |VNFT|)
RECOVERY TIME
LATENCY
FAULT
OVRFLW
DIGITAL OUTPUT
DATA AT DOUT
Figure 4. High-Frequency Analog Input Overvoltage Detection and Recovery
相关PDF资料
PDF描述
ISL3174EIBZ-T TXRX ESD 3.3V RS-485/422 8-SOIC
ISL3173EIUZ-T TXRX ESD 3.3V RS-485/422 10-MSOP
ISL3173EIBZ-T TXRX ESD 3.3V RS-485/422 14-SOIC
MS27468T15B5PB CONN RCPT 5POS JAM NUT W/PINS
MAX1243ACSA+ IC ADC 10BIT SERIAL 8-SOIC
相关代理商/技术参数
参数描述
MAX11068EVKIT 功能描述:电源管理IC开发工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT SMART BATT MEASUREMENT 12CH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX11068EVKIT+ 功能描述:电源管理IC开发工具 Programmers, Development Systems Eval and Demo Boards and Kits - KIT SMART BATT MEASUREMENT 12CH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX11068EVMINIQU+ 功能描述:电池管理 Automotive Battery Sensor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX11068GUU/V+ 功能描述:电池管理 12Ch High-V Smart Bat Msr System RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MAX11068GUU/V+T 功能描述:电池管理 12Ch High-V Smart Bat Msr System RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel