- 您现在的位置：买卖IC网 > PDF目录17006 > MAX110EVC32-DIP (Maxim Integrated Products)EVAL KIT FOR MAX110 PDF资料下载
参数资料
| 型号： | MAX110EVC32-DIP |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX110 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 14 |
| 采样率（每秒）： | 50 |
| 数据接口： | 串行 |
| 输入范围： | ±VREF |
| 在以下条件下的电源（标准）： | 4.35mW @ 50SPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX110，MAX111 |
| 已供物品： | 2 板，CD |
MAX110/MAX111
Low-Cost, 2-Channel, ±14-Bit Serial ADCs
______________________________________________________________________________________
11
ADC Operation
The output data from the MAX110/MAX111 is arranged
in twos-complement format (Figures 4, 5). The sign bit
(POL) is shifted out first, followed by the overrange bit
(OR), and the 14 data bits (MSB first) (see Figure 6).
The MAX110 operates from ±5V power supplies and
converts low-frequency analog signals in the ±3V
range when using the maximum reference voltage of
VREF = 3V (VREF = VREF+ - VREF-). Within the ±3V input
range, greater accuracy is obtained within ±2.5V (see
Electrical Characteristics for details). Note that a nega-
tive input voltage is defined as VIN- > VIN+. For the
MAX110, the absolute voltage at any analog input pin
must remain within the (VSS + 2.25V) to (VDD - 2.25V)
range.
The MAX111 operates from a single +5V supply and
converts low-frequency differential analog signals in the
±1.5V range when using the maximum reference volt-
age of VREF = 1.5V. As indicated in the Electrical
Characteristics, greater accuracy is achieved within the
±1.2V range. The absolute voltage at any analog input
pin for the MAX111 must remain within 0V to VDD - 3.2V.
When VIN- > VIN+ the input is interpreted as negative.
The overrange bit (OFL) is provided to sense when the
input voltage level has exceeded the reference voltage
level. The converter does not “saturate” until the input
voltage is typically 20% larger. The linearity is not guar-
anteed in this range. Note that the overrange bit works
properly if the reference voltage remains within the rec-
ommended voltage range (see
Reference Inputs). If the
reference voltage exceeds the recommended input
range, the overrange bit may not operate properly.
Digital Interface—Starting a Conversion
Data is transferred into and out of the serial I/O shift
register by pulling CS low and applying a serial clock
at SCLK. This fully static shift register allows SCLK to
range from DC to 2MHz. Output data from the ADC is
clocked out on SCLK’s falling edge and should be read
on SCLK’s rising edge. Input data to the ADC at DIN is
clocked in on SCLK’s rising edge. A new conversion
begins when CS returns high, provided the MSB in the
input control word (NO-OP) is a 1 (see
Using the
MAX110/MAX111 with MICROWIRE, SPI, and QSPI
Serial Interfaces). Figure 6 shows the detailed serial-
interface timing diagram.
C
CS
S must remain high during the conversion (while
BUSY remains low). Bringing CS low during the conver-
sion causes the ADC to stop converting, and may
result in erroneous output data.
Using the MAX110/MAX111 with SPI, QSPI, and
MICROWIRE Serial Interfaces
Figure 7 shows the most common serial-interface con-
nections. The MAX110/MAX111 are compatible with
SPI, QSPI (CPHA = 0, CPOL = 0), and MICROWIRE
serial-interface standards.
XCLK
TTL/CMOS
RCSEL
GND
+5V
-5V (0V)
( ) ARE FOR MAX111.
VDD
VSS (AGND)
MAX110
MAX111
Figure 3b. Connection for Internal RC-Oscillator Mode—XCLK
connects to the internal RC oscillator. Note, the pull-up resistor
is not necessary if the internal oscillator is never shut down.
XCLK
RCSEL
1M
GND
+5V
-5V (0V)
VDD
+5V
VSS (AGND)
MAX110
MAX111
( ) ARE FOR MAX111.
Figure 3a. Connection for External-Clock Mode
相关PDF资料 |
PDF描述 |
|---|---|
| 380LX153M016J022 | CAP ALUM 15000UF 16V 20% SNAP |
| SRR0603-221KL | INDUCTOR PWR 220UH 10% SHLD SMD |
| LGU2G221MELZ | CAP ALUM 220UF 400V 20% SNAP |
| MAX11040KEVKIT# | KIT EVAL FOR MAX11040 W/FMC CONN |
| 380LX221M200J202 | CAP ALUM 220UF 200V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX110EVKIT | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX110/MAX111 |
| MAX110EVKIT-DIP | 功能描述:数据转换 IC 开发工具 MAC110/1 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX110EWE | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Analog-to-Digital Converter， 15-Bit |
| MAX110-MAX111 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Cost, 2-Channel, 【14-Bit Serial ADCs |
| MAX110MJE | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Analog-to-Digital Converter， 15-Bit |
发布紧急采购，3分钟左右您将得到回复。