- 您现在的位置：买卖IC网 > PDF目录17011 > MAX1110EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX1110 PDF资料下载
参数资料
| 型号： | MAX1110EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX1110 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 50k |
| 数据接口： | 串行 |
| 输入范围： | 0 ~ VREF |
| 在以下条件下的电源（标准）： | 0.23mW @ 50kSPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX1110，MAX1112 |
| 已供物品： | 板，CD |
MAX1110/MAX1111
+2.7V, Low-Power, Multichannel,
Serial 8-Bit ADCs
______________________________________________________________________________________
11
in control bytes of $FF (hex), which trigger single-
ended, unipolar conversions on CH7 (MAX1110) or
CH3 (MAX1111) in external clock mode without power-
ing down between conversions. In external clock mode,
the SSTRB output pulses high for two clock periods
before the most significant bit of the 8-bit conversion
result is shifted out of DOUT. Varying the analog input
alters the output code. A total of 10 clock cycles is
required per conversion. All transitions of the SSTRB
and DOUT outputs occur on SCLK’s falling edge.
How to Start a Conversion
A conversion is started by clocking a control byte into
DIN. With CS low, each rising edge on SCLK clocks a bit
from DIN into the MAX1110/MAX1111’s internal shift reg-
ister. After CS falls, the first arriving logic “1” bit at DIN
defines the MSB of the control byte. Until this first start bit
arrives, any number of logic “0” bits can be clocked into
DIN with no effect. Table 3 shows the control-byte format.
The MAX1110/MAX1111 are compatible with MICROWIRE,
SPI, and QSPI devices. For SPI, select the correct clock
polarity and sampling edge in the SPI control registers:
set CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and
QSPI all transmit a byte and receive a byte at the same
time. Using the Typical Operating Circuit (Figure 3), the
simplest software interface requires three 8-bit transfers
to perform a conversion (one 8-bit transfer to configure
the ADC, and two more 8-bit transfers to clock out the
8-bit conversion result). Figure 6 shows the MAX1110/
MAX1111 common serial-interface connections.
1F
0.1F
VDD
DGND
AGND
CS
SCLK
DIN
DOUT
SSTRB
SHDN
+3V
N.C.
0.01F
CH7 (CH3)
COM
REFOUT
REFIN
C1
1F
0V TO
+2.048V
ANALOG
INPUT
OSCILLOSCOPE
CH1
CH2
CH3
CH4
*FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FF (HEX)
( ) ARE FOR THE MAX1111.
MAX1110
MAX1111
+3V
500kHz
OSCILLATOR
SCLK
SSTRB
DOUT*
Figure 5. Quick-Look Circuit
Table 4. Full-Scale and Zero-Scale Voltages
UNIPOLAR MODE
VREFIN + COM
+VREFIN/2
+ COM
Full Scale
COM
-VREFIN/2
+ COM
Positive
Full Scale
Zero Scale
Zero
Scale
BIPOLAR MODE
Negative
Full Scale
相关PDF资料 |
PDF描述 |
|---|---|
| GCM15DSES | CONN EDGECARD 30POS .156 EYELET |
| GEM36DSEN | CONN EDGECARD 72POS .156 EYELET |
| SDR1006-471KL | INDUCTOR POWER 470UH 0.42A SMD |
| PCM16XH1 | PROCESSOR MODULE FOR F83,84,84A |
| GCM18DRKS | CONN EDGECARD 36POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1110EVL11-DIP | 功能描述:数据转换 IC 开发工具 MAX1110L11-Dip Eval RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1110MJP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1111 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:+2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX11110 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs |
| MAX11110AUT+ | 制造商:Maxim Integrated Products 功能描述:SMALL, 2.2V TO 3.6V, LOW-POWER, 1-/2-CHANNEL, SERIAL, 8-/10- - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。