参数资料
| 型号： | MAX1112EAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT LP 20-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 位数： | 8 |
| 采样率（每秒）： | 50k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 680µW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个伪差分，单极；4 个伪差分，双极 |
MAX1112/MAX1113
+5V, Low-Power, Multi-Channel,
Serial 8-Bit ADCs
______________________________________________________________________________________
11
in control bytes of $FF (hex), which trigger single-
ended, unipolar conversions on CH7 (MAX1112) or
CH3 (MAX1113) in external clock mode without power-
ing down between conversions. In external clock mode,
the SSTRB output pulses high for two clock periods
before the most significant bit (MSB) of the 8-bit con-
version result is shifted out of DOUT. Varying the ana-
log input alters the output code. A total of 10 clock
cycles is required per conversion. All transitions of the
SSTRB and DOUT outputs occur on SCLK’s falling
edge.
How to Start a Conversion
A conversion is started by clocking a control byte into
DIN. With CS low, each rising edge on SCLK clocks a bit
from DIN into the MAX1112/MAX1113’s internal shift reg-
ister. After CS falls, the first arriving logic “1” bit at DIN
defines the MSB of the control byte. Until this first start bit
arrives, any number of logic “0” bits can be clocked into
DIN with no effect. Table 3 shows the control-byte format.
The
MAX1112/MAX1113
are
compatible
with
MICROWIRE, SPI, and QSPI devices. For SPI, select the
correct clock polarity and sampling edge in the SPI con-
trol registers: set CPOL = 0 and CPHA = 0. MICROWIRE,
SPI, and QSPI all transmit a byte and receive a byte at the
same time. Using the Typical Operating Circuit (Figure 3),
the simplest software interface requires three 8-bit trans-
fers to perform a conversion (one 8-bit transfer to config-
ure the ADC, and two more 8-bit transfers to clock out the
1F
0.1F
VDD
DGND
AGND
CS
SCLK
DIN
DOUT
SSTRB
SHDN
+5V
N.C.
0.01F
CH7 (CH3)
COM
REFOUT
REFIN
C1
1F
0V TO
+4.096V
ANALOG
INPUT
OSCILLOSCOPE
CH1
CH2
CH3
CH4
*FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FF (HEX)
( ) ARE FOR THE MAX1113.
MAX1112
MAX1113
+5V
500kHz
OSCILLATOR
SCLK
SSTRB
DOUT*
Figure 5. Quick-Look Circuit
Table 4. Full-Scale and Zero-Scale Voltages
UNIPOLAR MODE
VREFIN + COM
+VREFIN/2
+ COM
Full Scale
COM
-VREFIN/2
+ COM
Positive
Full Scale
Zero Scale
Zero
Scale
BIPOLAR MODE
Negative
Full Scale
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72615L50J | IC FIFO BY SYNC 512X18X2 68PLCC |
| AMIS42673ICAG1RG | TRANSCEIVER CAN HS 3.3V 8SOIC |
| IDT72V3662L15PF8 | IC FIFO 8192X36 15NS 120QFP |
| MS3111P14-12P | CONN RCPT 12POS CBL MNT W/PINS |
| IDT72805LB15BG8 | IC FIFO SYNC DUAL 256X18 121BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1112EPP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1112EPP+ | 功能描述:模数转换器 - ADC 5V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1112EVKIT | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX1110/MAX1112 |
| MAX1112-MAX1113 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs |
| MAX1112MJP | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。