- 您现在的位置：买卖IC网 > PDF目录9898 > MAX1204AEAP+T (Maxim Integrated Products)IC ADC 10BIT 8CH 20-SSOP PDF资料下载
参数资料
| 型号： | MAX1204AEAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/23页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 8CH 20-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 位数： | 10 |
| 采样率（每秒）： | 133k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 640mW |
| 电压电源： | 双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个差分，单极；4 个差分，双极 |
MAX1204
5V, 8-Channel, Serial, 10-Bit ADC
with 3V Digital Interface
10
Maxim Integrated
Input Bandwidth
The ADC’s input tracking circuitry has a 4.5MHz
small-signal bandwidth. Therefore, it is possible to digi-
tize high-speed transient events and measure periodic
signals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Input Range and Input Protection
Internal protection diodes, which clamp the analog
inputs to VDD and VSS, allow the analog input pins to
swing from (VSS - 0.3V) to (VDD + 0.3V) without dam-
age. However, for accurate conversions near full scale,
the inputs must not exceed VDD by more than 50mV, or
be lower than VSS by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of
off-channels over 2mA, as excessive current
degrades on-channel conversion accuracy.
The full-scale input voltage depends on the voltage at
REF (Tables 1a and 1b).
Quick Look
Use the circuit of Figure 5 to quickly evaluate the
MAX1204’s analog performance. The MAX1204 requires
that a control byte be written to DIN before each conver-
sion. Tying DIN to +3V feeds in control byte $FF hex,
which triggers single-ended unipolar conversions on
CH7 in external clock mode without powering down
between conversions. In external clock mode, the
SSTRB output pulses high for one clock period before
the most significant bit of the conversion result shifts out
of DOUT. Varying the analog input to CH7 alters the
sequence of bits from DOUT. A total of 15 clock cycles
per conversion is required. All SSTRB and DOUT output
transitions occur on SCLK’s falling edge.
How to Start a Conversion
Clocking a control byte into DIN starts conversion on
the MAX1204. With CS low, each rising edge on SCLK
clocks a bit from DIN into the MAX1204’s internal shift
register. After CS falls, the first logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with
no effect. Table 2 shows the control-byte format.
The MAX1204 is fully compatible with MICROWIRE and
SPI devices. For SPI, select the correct clock polarity
and sampling edge in the SPI control registers: set
CPOL = 0 and CPHA = 0. MICROWIRE and SPI both
transmit a byte and receive a byte at the same time.
Using the
Typical Operating Circuit, the simplest soft-
ware interface requires only three 8-bit transfers to per-
form a conversion (one 8-bit transfer to configure the
ADC, and two more 8-bit transfers to clock out the con-
version result).
Table 1b. Bipolar Full Scale, Zero Scale,
and Negative Full Scale
Table 1a. Unipolar Full Scale
and Zero Scale
REFERENCE
External
ZERO
SCALE
0V
Internal
at REFADJ
at REF
FULL SCALE
+4.096V
VREFADJ x 1.68
VREF
REFERENCE
-1/2 VREF
-1/2 VREFADJ x
1.68
-4.096V/2
NEGATIVE
FULL SCALE
ZERO
SCALE
0V
Internal
at
REFADJ
at REF
FULL SCALE
+4.096V / 2
+1/2 VREFADJ
x 1.68
+1/2 VREF
External
相关PDF资料 |
PDF描述 |
|---|---|
| ISL32177EFRZ | IC RCVR RS485/422 QD ESD 24QFN |
| VE-2WH-MX-F2 | CONVERTER MOD DC/DC 52V 75W |
| ICL7109CMH+TD | IC ADC 12BIT 3-ST 44-MQFP |
| ISL32175EIVZ | IC RCVR RS485/422 QD ESD 16TSSOP |
| VE-2WF-MX-F4 | CONVERTER MOD DC/DC 72V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1204AEPP | 功能描述:模数转换器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1204AEPP+ | 功能描述:模数转换器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1204BCAP | 功能描述:模数转换器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1204BCAP+ | 功能描述:模数转换器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1204BCAP+T | 功能描述:模数转换器 - ADC 10-Bit 8Ch 133ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。