- 您现在的位置：买卖IC网 > PDF目录17007 > MAX1231EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX1231 PDF资料下载
参数资料
| 型号： | MAX1231EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX1231 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 300k |
| 数据接口： | 串行 |
| 输入范围： | ±VREF/2 |
| 在以下条件下的电源（标准）： | 1.86mW @ 300kSPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX1231 |
| 已供物品： | 板，CD |
MAX1227/MAX1229/MAX1231
12-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
15
Temperature Measurements
The MAX1227/MAX1229/MAX1231 perform tempera-
ture measurements with an internal diode-connected
transistor. The diode bias current changes from 68A
to 4A to produce a temperature-dependent bias volt-
age difference. The second conversion result at 4A is
subtracted from the first at 68A to calculate a digital
value that is proportional to absolute temperature. The
output data appearing at DOUT is the above digital
code minus an offset to adjust from Kelvin to Celsius.
The reference voltage used for the temperature mea-
surements is derived from the internal reference source
to ensure that 1 LSB corresponds to 1/8 of a degree.
Output Data Format
Figures 4–7 illustrate the conversion timing for the
MAX1227/MAX1229/MAX1231. The 12-bit conversion
result is output in MSB-first format with four leading
zeros. DIN data is latched into the serial interface on
the rising edge of SCLK. Data on DOUT transitions on
the falling edge of SCLK. Conversions in clock modes 00
and 01 are initiated by CNVST. Conversions in clock
modes 10 and 11 are initiated by writing an input data
byte to the conversion register. Data is binary for unipo-
lar mode and two’s complement for bipolar mode.
BIT NAME
BIT
FUNCTION
UCH0/1
7 (MSB)
Set to 1 to configure AIN0 and AIN1 for unipolar differential conversion.
UCH2/3
6
Set to 1 to configure AIN2 and AIN3 for unipolar differential conversion.
UCH4/5
5
Set to 1 to configure AIN4 and AIN5 for unipolar differential conversion.
UCH6/7
4
Set to 1 to configure AIN6 and AIN7 for unipolar differential conversion.
UCH8/9
3
Set to 1 to configure AIN8 and AIN9 for unipolar differential conversion (MAX1229/MAX1231 only).
UCH10/11
2
Set to 1 to configure AIN10 and AIN11 for unipolar differential conversion (MAX1229/MAX1231 only).
UCH12/13
1
Set to 1 to configure AIN12 and AIN13 for unipolar differential conversion (MAX1231 only).
UCH14/15
0 (LSB)
Set to 1 to configure AIN14 and AIN15 for unipolar differential conversion (MAX1231 only).
Table 4. Unipolar Mode Register (Addressed Through Setup Register)
BIT NAME
BIT
FUNCTION
BCH0/1
7 (MSB)
Set to 1 to configure AIN0 and AIN1 for bipolar differential conversion.
BCH2/3
6
Set to 1 to configure AIN2 and AIN3 for bipolar differential conversion.
BCH4/5
5
Set to 1 to configure AIN4 and AIN5 for bipolar differential conversion.
BCH6/7
4
Set to 1 to configure AIN6 and AIN7 for bipolar differential conversion.
BCH8/9
3
Set to 1 to configure AIN8 and AIN9 for bipolar differential conversion (MAX1229/MAX1231 only).
BCH10/11
2
Set to 1 to configure AIN10 and AIN11 for bipolar differential conversion (MAX1229/MAX1231 only).
BCH12/13
1
Set to 1 to configure AIN12 and AIN13 for bipolar differential conversion (MAX1231 only).
BCH14/15
0 (LSB)
Set to 1 to configure AIN14 and AIN15 for bipolar differential conversion (MAX1231only).
Table 5. Bipolar Mode Register (Addressed Through Setup Register)
相关PDF资料 |
PDF描述 |
|---|---|
| 0210490251 | CABLE JUMPER 1.25MM .254M 18POS |
| GSM11DSEN-S13 | CONN EDGECARD 22POS .156 EXTEND |
| HW-DLN-3C | ACCY ISP CABLE 8PIN AMP 10P CONN |
| MAX11040DBEVKIT+ | KIT EVALUATION FOR MAX11040 |
| MAX1231BEVKIT# | KIT EVALUATION FOR 12BIT ADCS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1232C/D | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX1232C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX1232CPA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX1232CPA+ | 功能描述:监控电路 MPU Monitor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX1232CSA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。