- 您现在的位置：买卖IC网 > PDF目录1935 > MAX13041ASD/V+T (Maxim Integrated Products)IC CAN TXRX +/-80V HS 14SOIC PDF资料下载
参数资料
| 型号： | MAX13041ASD/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC CAN TXRX +/-80V HS 14SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | CAN |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
MAX13041
In the lowest-power mode, the MAX13041 disables exter-
nal voltage regulators to provide a sleep mode for the
entire node. The MAX13041 restores power to the node
upon a logic transition on WAKE or detection of CAN
bus activity.
The operating mode is determined by an internal state
machine controlled by EN and
STB, as well as several
internal flags (see Table 1 and Figure 4).
Normal Mode
The MAX13041 provides full bidirectional CAN commu-
nication in normal mode. Drive TXD to transmit data on
the differential CAN bus lines CANH and CANL. The
CAN bus state is presented on RXD, a level-shifted
logic output. SPLIT is biased to VCC/2 to allow CAN bus
common-mode stabilization. INH is logic-high, enabling
one or more external voltage regulators (see Table 1).
PWON/Listen-Only Mode
In PWON/listen-only mode, the CAN transmitter is dis-
abled. The CAN receiver remains active and the CAN
bus state is presented on RXD, a level-shifted logic out-
put. As in normal mode, SPLIT is biased to VCC/2 to
allow CAN bus common-mode stabilization. INH is
logic-high, enabling one or more external voltage regu-
lators (see Table 1).
Standby Mode
Standby mode is the first low-power operating mode.
The CAN transmitter and receiver are disabled, and a
low-power receiver is enabled to monitor the CAN bus
for activity. To reduce power consumption, common-
mode stabilization is disabled. SPLIT becomes high
impedance, and CANH and CANL are biased to
ground by the termination resistors. INH remains logic-
high, enabling one or more external voltage regulators
(see Table 1).
Go-to-Sleep Command Mode
Go-to-sleep command mode is part of the controlled
sequence for entering sleep mode. The MAX13041
remains in go-to-sleep command mode for a hold time of
56s (max), and subsequently enters sleep mode if no
wake events are detected. During the hold time, if the
state of EN or
STB changes, or if the UVBAT, PWON, or
wake-up flags are set, the go-to-sleep sequence is
aborted. During go-to-sleep command mode, functionali-
ty is the same as in standby mode.
Sleep Mode
Sleep mode is the lowest-power operating mode. The
CAN transmitter and receiver are disabled, and a low-
power receiver is enabled to monitor the CAN bus for
±80V Fault-Protected High-Speed CAN Transceiver
with Low-Power Management and Wake-On CAN
12
______________________________________________________________________________________
CONTROL PINS
INTERNAL FLAGS
STB
EN
UVNOM
UVBAT
PWON, WAKE-UP
OPERATING MODE
INH
SET
X
SLEEP (Notes 6, 7)
FLOATING
EITHER FLAG SET
STANDBY
H
XX
CLEAR
SET
BOTH FLAGS CLEAR
STANDBY FROM ANY OTHER MODE
H
EITHER FLAG SET
STANDBY
H
NO CHANGE FROM SLEEP MODE
FLOATING
LL
CLEAR
BOTH FLAGS CLEAR
STANDBY FROM ANY OTHER MODE
H
EITHER FLAG SET
STANDBY
H
NO CHANGE FROM SLEEP MODE
FLOATING
LH
CLEAR
BOTH FLAGS CLEAR
GO-TO-SLEEP COMMAND MODE FROM
ANY OTHER MODE (Note 7)
H
HL
CLEAR
X
PWON/LISTEN-ONLY
H
HH
CLEAR
X
NORMAL (Note 9)
H
Table 1. Operating Modes
Note 6: Setting the PWON or wake-up flags clears UVNOM flag.
Note 7: The MAX13041 enters sleep mode from any other mode when UVNOM is set. INH becomes high impedance.
Note 8: When go-to-sleep command mode is selected for longer than tH(MIN), the MAX13041 enters sleep mode.
INH becomes high impedance.
Note 9: PWON and wake-up flags are cleared upon entering normal mode.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX13051ASA+ | IC TRANSCEIVER CAN 8-SOIC |
| MAX13054ASA+T | IC TRANSCEIVER CAN HS 8-SOIC |
| MAX13087ECPA+ | IC TXRX RS485/422 5V ESD 8-DIP |
| MAX13174ECAG+ | IC CBL TERMINATION NETWRK 24SSOP |
| MAX13184EESD+ | IC TXRX RS-485 +5.0V ESD 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX13042EEBC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX13042EEBC+T | 功能描述:转换 - 电压电平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13042EETD+ | 制造商:Maxim Integrated Products 功能描述:1.62V TO 3.6V IMPROVED HIGH-SPEED L - Rail/Tube |
| MAX13042EETD+T | 功能描述:转换 - 电压电平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13042EEVKIT+ | 功能描述:电源管理IC开发工具 MAX13042E Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。