- 您现在的位置：买卖IC网 > PDF目录10565 > MAX1363EUB+ (Maxim Integrated Products)IC SYSTEM MON 12BIT 4CH 10-UMAX PDF资料下载
参数资料
| 型号： | MAX1363EUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/25页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MON 12BIT 4CH 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 位数： | 12 |
| 采样率（每秒）： | 133k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 444.4mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
clearing all alarms or by initiating an SMBus alert during
an alarm condition (see the
SMBus Alert section).
The Delay 2, Delay 1, Delay 0 bits set the speed of
monitoring by changing the delay between conver-
sions. Delay 2, 1, 0 = 000 sets the maximum possible
speed; 001 divides the maximum speed by ~2.
Increasing delay values further divides the previous
speed by two.
INT_EN controls the open-drain
INT output. Set INT_EN
to 1 to enable the hardware interrupt. Set INT_EN to 0
to disable the hardware interrupt output. The
INT output
tri-states when disabled or when there are no alarms.
The master can also poll the alarm status register at
any time to check the alarm status.
Repeat clocking channel threshold data up to the chan-
nel programmed by CS1 and CS0 (Table 12). For differ-
ential input mode, omit odd channels; the lower and
upper threshold data applies to channel pairs. There is
no need to clock in dummy data for odd (or even)
channels (Table 6).
To disable alarming on a specific channel, set the lower
threshold to 0x800 and the upper threshold to 0x7FF for
bipolar mode, or set the lower threshold to 0x000 and
the upper threshold to 0xFFF for unipolar mode.
MAX1363/MAX1364
4-Channel, 12-Bit System Monitors with Programmable
Trip Window and SMBus Alert Response
______________________________________________________________________________________
19
Alarm reset, scan
speed, INT_EN ,
(8 bits)
AIN0 thresholds
(24 bits)
AIN1 thresholds
(skip if differential mode, or
CS1, CS0 < 1) (24 bits)
AIN2 thresholds (skip if
CS1, CS0 < 2)
(24 bits)
AIN3 thresholds (skip if differential
mode, or CS1, CS0 < 3)
(24 bits)
Table 9. Monitor-Mode Setup Data Format
RESET
ALARM CH 0
RESET
ALARM CH 1
RESET
ALARM CH 2
RESET
ALARM CH 3
DELAY 2
DELAY 1
DELAY 0
INT_EN
0/1
Table 10. Alarm Reset, Scan Speed Register, and INT_EN Data Format
DELAY 2 DELAY 1
DELAY 0
MONITOR-MODE
CONVERSION RATE
(ksps)
0
133.0*
001
66.5
010
33.3
011
16.6
100
8.3
101
4.2
110
2.0
111
1.0
Table 11. Delay Settings
*
When using delay = [0,0,0] in internal reference mode and
AIN3/REF configured as a REF output, the MAX1363/MAX1364
may exhibit a code-dependent gain error due to insufficient
internal reference drive. Gain error caused by this phenomenon
is typically less than 1%FSR (0.1F CREF) and increases with a
larger CREF. Avoid this gain error by using an external reference,
VDD, as a reference or use an internal reference with AIN3/REF
as an analog input (see Table 4). Alternatively, choose delay bits
other than [0,0,0] to lower the conversion rate.
BYTE
B7
B6
B5
B4
B3
B2
B1
B0
ACKNOWLEDGE
1
LT11
(MSB)
LT10
LT9
LT8
LT7
LT6
LT5
LT4
ACK
2
LT3
LT2
LT1
LT0 (LSB)
UT11
(MSB)
UT10
UT9
UT8
ACK
3
UT7
UT6
UT5
UT4
UT3
UT2
UT1
UT0 (LSB)
ACK
Table 12. Lower and Upper Threshold Data Format
X = Don’t care.
ACK = Acknowledge.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1130AISW#PBF | IC TXRX 5V RS232 LP W/CAP 28SOIC |
| PX0911/04/P | CONN PLUG 4POS W/PINS |
| MAX1169BEUD+ | IC ADC 16BIT SER 14-TSSOP |
| 206837-1 | CONN PLUG CPC 24POS STD SER 1 |
| LT1130AISW | IC TXRX 5V RS232 LP W/CAP 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1363EUB+ | 功能描述:模数转换器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EUB+T | 功能描述:模数转换器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EUB-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EVKIT | 功能描述:数据转换 IC 开发工具 Evaluation Kit for the MAX1361/MAX1363 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1363LEUB+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 133KSPS 12-BIT SERL 10PIN UMAX - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。