- 您现在的位置：买卖IC网 > PDF目录10565 > MAX1363EUB+ (Maxim Integrated Products)IC SYSTEM MON 12BIT 4CH 10-UMAX PDF资料下载
参数资料
| 型号： | MAX1363EUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MON 12BIT 4CH 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 位数： | 12 |
| 采样率（每秒）： | 133k |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 444.4mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，单极；4 个单端，双极；2 个差分，单极；2 个差分，双极 |
MAX1363/MAX1364
Readback Mode
Select readback mode by setting CS3, CS2 to [1,1] in
the configuration byte. Begin a read operation to start
reading back monitor-setup data. Clock out delay bit
settings, INT_EN bit, and the lower and upper thresh-
olds programmed for each channel. Readback mode
follows exactly the same format as writing to the moni-
tor-setup data, with the exception of the first 4 alarm-
reset bits, which are always 1 (Table 13).
Reading in Monitor Mode
Reading in monitor mode reads back the alarm-status
register, latched-fault register, and current-conversion
results as shown in Table 14.
The MAX1363/MAX1364 register pointer loops back to
the beginning of the current-conversion result after
reading the last conversion result. Stop reading at any
time by asserting a STOP condition or NACK.
Note: The MAX1363/MAX1364 do not update the cur-
rent-conversion results register while reading in monitor
mode. Monitor mode resumes after a STOP condition
or NACK.
Alarm-Status Register and Latched-Fault Register
The latched-fault register records a snapshot of the
alarming channel at the instance that a fault condition is
asserted. An alarm-status bit of 1 (Table 15) indicates a
fault, and the data in the latched-fault register of the
corresponding channel contains the conversion result
that caused the alarm to trip. Resetting alarms does not
clear the latched-fault register, thus the latched-fault
register contains valid data only if an alarm status bit is
high for the given channel.
The current-conversion register contains the most
recent conversion results. If the user attempts to read
past the last result of the current-conversion register,
the MAX1363/MAX1364 wraps back to the beginning of
the current-conversion result.
The latched-fault register and current-conversion regis-
ter follow the data format in the
Reading a Conversion
(
Read Cycle) section. Register length depends on the
number of conversions in one monitoring sequence.
For example, when channel pairs 0/1 and channels 2/3
are monitored differentially, there are only two conver-
sion results to report. The latched-fault register is 2 x 16
bits long, after which two current-conversion results fol-
low. Likewise, if CS0 and CS1 limit the upper bound of
the channel scan range from CH0 to CH2 in single-
ended mode, the latched-fault register clocks out 3 x
16 bits of data followed by the current-conversion
results, also 3 x 16 bits.
4-Channel, 12-Bit System Monitors with Programmable
Trip Window and SMBus Alert Response
20
______________________________________________________________________________________
ALARM RESET/SCAN SPEED
AIN0
THRESHOLDS
AIN1 THRESHOLDS
(SKIP IF DIFFERENTIAL
MODE OR CS1, CS0 < 1)
AIN2 THRESHOLDS
(SKIP IF CS1, CS0 < 2)
AIN3 THRESHOLDS
(SKIP IF DIFFERENTIAL
MODE OR CS1, CS0 < 3)
1
D2 D1 D0 INT
24 bits
Table 13. Readback-Mode Format
ALARM-STATUS REGISTER
LATCHED-FAULT REGISTER
CURRENT-CONVERSION RESULTS
8 bits
16, 32, 48, or 64 bits
Table 14. Reading in Monitor-Mode Data Format
CH0 UP
CH0 LOW
CH1 UP
CH1 LOW
CH2 UP
CH2 LOW
CH3 UP
CH3 LOW
0/1
Table 15. Alarm-Status Register
0 = Not-alarm condition.
1 = Alarm condition.
AIN0
AIN1
AIN2
AIN3
16-bit read
Table 16. Latched-Fault and Current-
Conversion Register
相关PDF资料 |
PDF描述 |
|---|---|
| LT1130AISW#PBF | IC TXRX 5V RS232 LP W/CAP 28SOIC |
| PX0911/04/P | CONN PLUG 4POS W/PINS |
| MAX1169BEUD+ | IC ADC 16BIT SER 14-TSSOP |
| 206837-1 | CONN PLUG CPC 24POS STD SER 1 |
| LT1130AISW | IC TXRX 5V RS232 LP W/CAP 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1363EUB+ | 功能描述:模数转换器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EUB+T | 功能描述:模数转换器 - ADC 12-Bit 4Ch 133ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EUB-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1363EVKIT | 功能描述:数据转换 IC 开发工具 Evaluation Kit for the MAX1361/MAX1363 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1363LEUB+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL SAR 133KSPS 12-BIT SERL 10PIN UMAX - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。