- 您现在的位置：买卖IC网 > PDF目录20146 > MAX1365ECM+T (Maxim Integrated)IC PANEL METER 4.5 DIG 48LQFP PDF资料下载
参数资料
| 型号： | MAX1365ECM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/25页 |
| 文件大小： | 0K |
| 描述： | IC PANEL METER 4.5 DIG 48LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 显示器类型： | LED |
| 配置： | 7 段显示 |
| 数字或字符： | A/D，4.5 位数字 |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 带卷 (TR) |
Stand-Alone, 4.5-/3.5-Digit Panel Meters
with 4–20mA Output
During these 6s, the MAX1365 displays 1.2V to 1.5V
when a stable reference is detected. If a valid refer-
ence is not found, the MAX1365 times out after 6s and
begins enhanced offset calibration. Enhanced offset
calibration typically lasts 2s. The MAX1365 begins con-
verting after enhanced offset calibration.
Reference
ADC Reference
The MAX1365/MAX1367 reference sets the full-scale
range of the ADC transfer function. With a nominal
2.048V reference, the ADC full-scale range is ±2V with
RANGE = GND. With RANGE = DV DD, the full-scale
range is ±200mV. A decreased reference voltage
decreases full-scale range (see the Transfer Functions
section).
The ADC of the MAX1365/MAX1367 can accept either
an external reference or an internal reference (INTREF).
The INTREF logic selects the reference mode. For inter-
nal-reference operation, set INTREF to DV DD, connect
REF- to GND, and bypass REF+ to GND with a 4.7μF
capacitor. The internal reference provides a nominal
2.048V source between REF+ and GND. The internal-
reference temperature coefficient is typically
40ppm/°C.
For external-reference operation, set INTREF to GND.
REF+ and REF- are fully differential. For a valid exter-
nal-reference input, VREF+ must be greater than VREF-.
Bypass REF+ and REF- with a 0.1μF or greater capaci-
tor to GND in external-reference mode.
Figure 6 shows the MAX1365/MAX1367 operating with
an external differential reference. In this figure, REF- is
connected to the top of the strain gauge and REF+ is
connected to the midpoint of the resistor-divider of
the supply.
DAC Reference
The DAC of the MAX1365/MAX1367 accept either an
external reference or an internal reference. The REFSELE
enables or disables the internal reference. For external-
reference operation, disable the DAC reference buffer by
setting REFSELE to DV DD and connect a voltage source
to REF_DAC.
For internal-reference operation, enable the DAC refer-
ence buffer by setting REFSELE to GND. In this mode,
leave REFDAC floating.
In either internal or external reference operation,
bypass REF_DAC with a 0.1μF capacitor to GND.
Choose a reference with output impedance (load regu-
lation equivalent) of 100m ? or less, such as the
MAX6126. For best performance, use an external
reference source for the ADC and DAC.
DAC Operation
For the MAX1365/MAX1367, a voltage proportional to
the ADC input is available at DACVOUT. Connect
DACVOUT to CONV_IN for normal operation. See
Figure 11 for the DAC transfer function.
Offset Calibration
The MAX1365/MAX1367 offer on-chip offset calibration.
The device offset calibrates during every conver-
sion cycle.
Enhanced Offset Calibration
Enhanced offset calibration is a more accurate calibra-
tion method that is needed in the case of the ±200mV
range and 4.5-digit resolution. In addition to enhanced
offset calibration at power-up, the MAX1365/MAX1367
perform enhanced calibration on demand by connect-
ing HOLD to AV DD for > 2s.
Peak
The MAX1365/MAX1367 feature peak-detection circuitry.
When activated, the devices display only the highest
voltage measured to the LED. First, the current ADC
result is displayed. The new ADC conversion result is
compared to the current result. If the new value is larg-
er than the previous peak value, the new value is dis-
played. If the new value is less than the previous peak
value, the display remains unchanged. Connect PEAK
to GND to clear the peak value and disable the peak
function. See Table 1 for LED Display priority.
Hold
The MAX1365/MAX1367 feature data-hold circuitry.
When activated, the device holds the current reading
on the LED.
Strain-Gauge Measurement
Connect the differential inputs of the MAX1365/
MAX1367 to the bridge network of the strain gauge. In
Figure 6, the analog supply voltage powers the bridge
network and the MAX1365/MAX1367, along with the
reference voltage. The MAX1365/MAX1367 handle an
analog input voltage range of ±200mV and ±2V full
scale. The analog/reference inputs of the parts allow
the analog input range to have an absolute value of
anywhere between -2.2V and +2.2V.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6961AMH+D | IC DRVR LED 8X8 44-MQFP |
| VI-22V-CX-F2 | CONVERTER MOD DC/DC 5.8V 75W |
| HR-3U-2500L2X4 | BATT PACK 9.6V AA BUTTON NIMH |
| HCC50DRES-S13 | CONN EDGECARD 100PS .100 EXTEND |
| VI-22V-CX-F1 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1366ECM | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX1366ECM+ | 功能描述:LED显示驱动器 Stand-Alone 4.5Digit Panel Meters RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX1366ECM+T | 功能描述:LED显示驱动器 Stand-Alone 4.5Digit Panel Meters RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX1366ECM-T | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX1366EVKIT | 功能描述:LED 照明开发工具 MAX1366 EVAL KIT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。