参数资料
| 型号： | MAX1414CAI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/48页 |
| 文件大小： | 0K |
| 描述： | IC DAS 16BIT LP 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 类型： | 数据采集系统（DAS） |
| 分辨率（位）： | 16 b |
| 采样率（每秒）： | 60 |
| 数据接口： | 串行 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
MAX1407/MAX1408/MAX1409/MAX1414
Low-Power, 16-Bit Multichannel DAS with
Internal Reference,10-Bit DACs, and RTC
32
______________________________________________________________________________________
WE: Write Enable bit. WE must be set to “1” before any
write operation to the clock and the alarm register. A
logic 0 disables write operations to the clock and alarm
registers, including the AE bit. The WE signal takes
effect after the 8th SCLK rising edge for an 8-bit write.
AE: Alarm Enable bit. A logic 0 disables the alarm func-
tion. When AE equals “1”, the ALIRQ bit in the Al_Status
register will be set to 1 whenever the current time
matches that of the alarm registers.
Real-Time Clock (RTC)
The RTC_Sec, RTC_Min, RTC_Hour, RTC_Date,
RTC_Month, RTC_Day, RTC_Year, and RTC_Century
registers can be accessed one register at a time or in
Burst mode (see RTC_BURST REGISTER section). The
RTC runs continuously and does not stop for read or
write operations. To prevent the data from changing
during a read operation, complete all read operations
on the RTC registers (single register reads and burst
reads) in less than 1ms.
Using single reads to read all the RTC registers could
lead to errors as much as a century. Since the registers
are updated between read operations, the register con-
tents may change before all RTC registers have been
read, when reading one register at a time. The most
accurate way to get the time information of the RTC
registers is with a burst read. In the burst read, a snap-
shot of the eight RTC registers (RTC_Sec, RTC_Min,
RTC_Hour, RTC_Date, RTC_Month, RTC_Day,
RTC_Year, RTC_Century) is taken once and read
sequentially with the MSB of the Seconds register first.
They must all be read out as a group of eight registers
of eight bits each, for proper execution of the burst
read function. The worst-case error that can occur
between the “actual” time and the “reported” time is
one second. As with a read operation, using single
writes to update the RTC can lead to collisions. To
guarantee an accurate update of the RTC, use the
Burst Write mode (see Alarm and RTC Programming
section).
The RTC defaults to 24-hr mode, 00:00:00, Sunday,
January 01, 1970 during power-up. January 01, 1970
falls on a Thursday, but since this RTC is not time-
based, the default values do not have an impact on the
functionality of the clock, and they merely provide some
means for testing. If the alarm or RTC registers are pro-
grammed to some unused states, the device chooses
the default values.
RTC_BURST REGISTER (01111)
Writing to this address begins the burst mode transfer.
In this mode, all the real-time clock registers are contin-
uously read or written starting with Bit 7 of the
RTC_Sec,
RTC_Min,
RTC_Hour,
RTC_Date,
RTC_Month, RTC_Day, RTC_Year, and RTC_Century
registers. When reading, the contents of DIN will be
ignored and each register’s 8-bit data will be clocked
out at DOUT on the falling edge of SCLK (total of 64
clock cycles). When writing, start with the Seconds’
register MSB first and continue through the Century
register (see Alarm and RTC Programming section).
ALARM/CLOCK_CTRL REGISTER (01110)
FIRST BIT (MSB)
(LSB)
NAME
WE
—————
—
AE
DEFAULT
000000
00
CH: Clock Halt bit. Writing a “1” to CH disables the
real-time clock and oscillator.
10SEC[2:0]: These are the 10 second bits (10–50 sec-
onds) of the RTC.
SEC[3:0]: These are the second bits (0–9 seconds) of
the RTC.
FIRST BIT (MSB)
(LSB)
NAME
CH
10SEC2
10SEC1
10SEC0
SEC3
SEC2
SEC1
SEC0
DEFAULT
0
RTC_SEC REGISTER (10000)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1441GUP/V+ | IC PROXMITY SENSOR 2CH 20-TSSOP |
| MAX14502AETL+T | IC CARD READER USB-SD 40-TQFN |
| MAX14505EWC+T | IC SWITCH DUAL SPDT 12WLP |
| MAX14523BATA/V+T | IC CURRENT LIMIT SWITCH 8TDFN |
| MAX1452AAE+T | IC SENSOR SIGNAL COND 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1414EAI | 制造商:Maxim Integrated Products 功能描述:LOW-POWER, 16-BIT MULTICHANNEL DAS WITH INTER - Bulk |
| MAX1414EAI+ | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Rail/Tube |
| MAX1414EAI+T | 制造商:Maxim Integrated Products 功能描述:LOW-POWER 16-BIT MULTICHANNEL DAS - Tape and Reel |
| MAX1415AENE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX1415AEUE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。