- 您现在的位置：买卖IC网 > PDF目录11652 > MAX1455AUE+ (Maxim Integrated Products)IC AUTO SNSR SIGNAL COND 16TSSOP PDF资料下载
参数资料
| 型号： | MAX1455AUE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/25页 |
| 文件大小： | 0K |
| 描述： | IC AUTO SNSR SIGNAL COND 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 类型： | 自动 |
| 输入类型： | 模拟 |
| 输出类型： | 模拟 |
| 电流 - 电源： | 6mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
and stored in the upper 3 bits of EEPROM location
161hex (EEPROM upper configuration byte).
The MAX1455 internal clock controls timing functions,
including the signal path gain, DAC functions, and com-
munications. It is recommended that, while in digital
mode, the Configuration register CLK bits be assigned
the values contained in EEPROM (upper configuration
byte). The 3 CLK bits represent a two’s-complement
number with a nominal clock adjustment of 9% per bit.
Table 12 shows the codes and adjustment available.
Any change to the CLK bit values contained in the
Configuration register must be followed by the
MAX1455 baud rate learning sequence (reinitialize and
initialize commands). To maximize the robustness of
the communication system during clock resetting only,
change the CLK bits by 1LSB value at a time. The rec-
ommended setting procedure for the Configuration reg-
ister CLK bits is, therefore, as follows. (Use a minimum
baud rate of 9600 during the setting procedure to pre-
vent potential overflow of the MAX1455 baud rate
counter with clock values near maximum.)
The following example is based on a required CLK
code of 010 binary:
1) Read the CLK bits (3MSBs) from EEPROM location
161hex. CLK = 010 binary.
2) Set the CLK bits in the Configuration register to 001
binary.
3) Send the reinitialize command, followed by the ini-
tialize (baud rate learning) command.
4) Set the CLK bits in the Configuration register to 010
binary.
MAX1455
Low-Cost Automotive Sensor Signal
Conditioner
______________________________________________________________________________________
15
Table 9. IRSA Decoding
IRSA[3:0]
DESCRIPTION
0000
Write IRSD[3:0] to DHR[3:0] (Data Hold register)
0001
Write IRSD[3:0] to DHR[7:4] (Data Hold register)
0010
Write IRSD[3:0] to DHR[11:8] (Data Hold register)
0011
Write IRSD[3:0] to DHR[15:12] (Data Hold register)
0100
Reserved
0101
Reserved
0110
Write IRSD[3:0] to ICRA[3:0] or IEEA[3:0] (Internal Calibration register address or internal EEPROM address
nibble 0)
0111
Write IRSD[3:0] to IEEA[7:4] (internal EEPROM address, nibble 1)
1000
Write IRSD[3:0] to IRSP[3:0] or IEEA[9:8] (Interface register set pointer where IRSP[1:0] is IEEA[9:8])
1001
Write IRSD[3:0] to CRIL[3:0] (Command register to internal logic)
1010
Write IRSD[3:0] to ATIM[3:0] (analog timeout value on read)
1011
Write IRSD[3:0] to ALOC[3:0] (analog location)
1100 to 1110
Reserved
1111
Write IRSD[3:0] = 1111bin to relearn the baud rate
Table 8. Control Location (CL[15:0])
FIELD
NAME
DESCRIPTION
15:8
CL[15:8]
Reserved
7:0
CL[7:0]
Control Location. Secure-Lock is activated by setting this to FFhex, which disables DIO serial
communications and connects OUT to PGA output.
相关PDF资料 |
PDF描述 |
|---|---|
| MCF51AC256ACLKE | MCU 32BIT 256K FLASH CAN 80-LQFP |
| MC908AP32CFBE | IC MCU 32K FLASH 8MHZ 44QFP |
| 221185-1 | CONN PLUG BNC 75 OHM DUAL CRIMP |
| PCF51JM128EVLK | MCU 32BIT 128K FLASH 80-LQFP |
| VI-JN4-IZ-B1 | CONVERTER MOD DC/DC 48V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1455AUE+ | 功能描述:板上安装温度传感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1455AUE+T | 功能描述:板上安装温度传感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1455AUE-T | 功能描述:板上安装温度传感器 Automotive Sensor Signal Conditioner RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1455C/D | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1455C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。