- 您现在的位置：买卖IC网 > PDF目录224186 > MAX1459AAP+T (MAXIM INTEGRATED PRODUCTS INC) 2-Wire, 4-20mA Smart Signal Conditioner PDF资料下载
参数资料
| 型号： | MAX1459AAP+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | 2-Wire, 4-20mA Smart Signal Conditioner |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封装： | 5.30 MM, 0.65 MM PITCH, SSOP-20 |
| 文件页数： | 14/24页 |
| 文件大小： | 243K |
| 代理商： | MAX1459AAP+T |
2) MAX1459 Reference Manual, which describes in
detail the architecture and functionality of the
MAX1459. This manual was developed for test engi-
neers familiar with data acquisition of sensor data
and provides sensor compensation algorithms and
test procedures.
3) MAX1459 Communication Software, which enables
programming of the MAX1459 from a computer (IBM
compatible), one module at a time.
4) Interface Adapter and Cable, which allow the con-
nection of the evaluation board to a PC parallel port.
MAX1459
Pilot Production System
Maxim understands that one of the biggest challenges
in pressure sensor design is the transition from proto-
type to production. To simplify this transition, Maxim
has developed the fully automated pilot production
system for volume applications.
The system consists of the Maxim 14XXDASBOARD
plus one or more 14XXMUXBOARD modules, a DVM,
an environmental chamber, and a pressure controller.
Only the 14XXDASBOARD and the 14XXMUXBOARD
modules are available through Maxim. The DVM, envi-
ronmental chamber, and pressure controller must be
acquired through other vendors.
The 14XXDASBOARD, in conjunction with the
14XXMUXBOARD modules, allow compensation of up to
112 units. IEEE-488 commands select the active DUT
and communicate with the MAX14XX application cir-
cuits. All system voltage measurements are multiplexed
for use with a single external DVM. Each DUT interfaces
to the 14XXMUXBOARD by means of a general-purpose
transition board, which provides digital interface signals
and low-noise analog inputs. The 14XXDASBOARD is
required to operate the 14XXMUXBOARD. All driver soft-
ware is incorporated into the 14XXDASBOARD firmware.
Sensor compensation procedure is implemented using
National Instruments’ LabView program.
MAX1459
2-Wire, 4–20mA
Smart Signal Conditioner
______________________________________________________________________________________
21
MAX1459
DIO
OUT
VDD
CS
MODULE 1
SCLK
VSS
VDD
VSS
TEST
OVEN
MAX1459
DIO
OUT
CS
MODULE 2
SCLK
DIO
VOUT
DIGITAL
MULTIPLEXER
+5V
CS[1:N]
CS1
BDRIVE
INP
INM
BDRIVE
INP
INM
BDRIVE
INP
INM
CS2
CSN
SCLK
MAX1459
DIO
OUT
CS
MODULE N
SCLK
DVM
Figure 15. Automated Test System Concept
LabView is a trademark of National Instruments.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1459CAP+ | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX1459AAP+ | 2-Wire, 4-20mA Smart Signal Conditioner |
| MAX147BEAP+ | +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX147BEAP+T | +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs |
| MAX147BCPP+ | +2.7V, Low-Power, 8-Channel, Serial 12-Bit ADCs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1459CAP+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX1459CAP+T | 制造商:Maxim Integrated Products 功能描述:SMART SGNL CONDITIONER 20SSOP - Tape and Reel |
| MAX1459CAP-T | 制造商:Maxim Integrated Products 功能描述:#EMPTY - Tape and Reel |
| MAX145ACPA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX145ACPA+ | 功能描述:模数转换器 - ADC 12-Bit 108ksps 5.25V High Speed ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。