- 您现在的位置：买卖IC网 > Datasheet目录471 > MAX1471EVKIT-315 (Maxim Integrated)EVAL KIT FOR MAX1471 315MHZ Datasheet资料下载
参数资料
| 型号： | MAX1471EVKIT-315 |
| 厂商： | Maxim Integrated |
| 文件页数： | 21/26页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX1471 315MHZ |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 接收器，ASK/FSK |
| 频率： | 315MHz |
| 适用于相关产品： | MAX1471 ~ 315MHz |
| 已供物品： | 板 |
315MHz/434MHz Low-Power, 3V/5V
ASK/FSK Superheterodyne Receiver
Table 6. Power Configuration Register (Address: 0x0)
BIT ID
LNA_EN
AGC_EN
MIXER_EN
FSKBB_EN
FSKPD_EN
ASKBB_EN
ASKPD_EN
SLEEP
BIT NAME
LNA enable
AGC enable
Mixer enable
FSK baseband
enable
FSK peak
detector enable
ASK baseband
enable
ASK peak
detector enable
Sleep mode
BIT LOCATION
(0 = LSB)
7
6
5
4
3
2
1
0
POWER-UP
STATE
0
0
0
0
0
0
0
0
FUNCTION
1 = Enable LNA
0 = Disable LNA
1 = Enable AGC
0 = Disable AGC
1 = Enable mixer
0 = Disable mixer
1 = Enable FSK baseband
0 = Disable FSK baseband
1 = Enable FSK peak detectors
0 = Disable FSK peak detectors
1 = Enable ASK baseband
0 = Disable ASK baseband
1 = Enable ASK peak detectors
0 = Disable ASK peak detectors
1 = Deep-sleep mode
0 = Normal operation
At the end of t RF , the MAX1471 stops driving DIO low
and enables ADATA, FDATA, and peak detectors if
chosen to be active in the power configuration register
(0x0). The CPU must be awake at this point, and must
hold DIO low for the MAX1471 to remain in operation.
The CPU must begin driving DIO low any time during
t LOW = t CPU + t RF . If the CPU fails to drive DIO low,
DIO is pulled high through the internal pullup resistor,
and the timer sequence is restarted, leaving the
MAX1471 powered down. Any time the DIO line is dri-
ven high while the DRX = 1, the DRX sequence is initi-
ated, as defined in Figure 12.
t RF is a 16-bit timer, configured through registers 0x7
(upper byte) and 0x8 (lower byte). The possible t RF set-
tings are in Table 12. The data written to the t RF register
(0x7 and 0x8) is multiplied by 120μs to give the total t RF
time. On power-up, the RF timer registers are set to
zero and must be written before using DRX mode.
Typical Power-Up Procedure
Here is a typical power-up procedure for receiving either
ASK or FSK signals at 315MHz in continuous mode:
1) Write 0x3000 to reset the part.
2) Write 0x10FE to enable all RF and baseband sections.
3) Write 0x135F to set the oscillator frequency register
to work with a 315MHz crystal.
4) Write 0x1120 to set FSKCALLSB for an accurate
FSK calibration.
5) Write 0x1201 to begin FSK calibration.
6) Read 0x2900 and verify that bit 0 is 1 to indicate
FSK calibration is done.
The MAX1471 is now ready to receive ASK or FSK data.
Due to the high sensitivity of the receiver, it is recom-
mended that the configuration registers be changed
only when not receiving data. Receiver desensitization
may occur, especially if odd-order harmonics of the
SCLK line fall within the IF bandwidth.
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1472EVKIT-433# | EVAL KIT MAX1472 |
| MAX1473EVKIT-433 | EVAL KIT MAX1473 |
| MAX1479EVKIT-315 | EVAL KIT FOR MAX1479 315MHZ |
| MAX19700EVKIT | EVAL KIT FOR MAX19700 |
| MAX19985AETX+T | IC MIXER DOWNCONV 36-TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1471EVKIT-433 | 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX1471EVSYS-315 | 功能描述:射频开发工具 MAX1471 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX1471EVSYS-433 | 功能描述:射频开发工具 MAX1471 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX1472AKA | 制造商:Maxim from Components Direct 功能描述:MAXIM MAX1472AKA RF ICS MISC - Tape and Reel 制造商:Maxim 功能描述:Maxim MAX1472AKA RF ICs Misc |
| MAX1472AKA+ | 制造商:Maxim Integrated Products 功能描述:LOW-PWR CRYSTAL-BASED ASK TRANSMITTER 8PIN SOT-23 - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。