- 您现在的位置：买卖IC网 > PDF目录17006 > MAX147EVC16-DIP (Maxim Integrated Products)EVAL KIT FOR MAX147 PDF资料下载
参数资料
| 型号： | MAX147EVC16-DIP |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX147 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 133k |
| 数据接口： | 串行 |
| 输入范围： | ±VREF/2 |
| 在以下条件下的电源（标准）： | 2.7mW @ 133kSPS |
| 工作温度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX147 |
| 已供物品： | 2 板，样品，CD |
PD0 CLOCK IN
tSSTRB
tCSH
tCONV
tSCK
SSTRB
SCLK
DOUT
tCSS
tDO
NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION.
CS
Figure 10. Internal Clock Mode SSTRB Detailed Timing
MAX146/MAX147
+2.7V, Low-Power, 8-Channel,
Serial 12-Bit ADCs
14
______________________________________________________________________________________
processor’s convenience, at any clock rate from 0MHz
to 2MHz. SSTRB goes low at the start of the conversion
and then goes high when the conversion is complete.
SSTRB is low for a maximum of 7.5s (SHDN = FLOAT),
during which time SCLK should remain low for best
noise performance.
An internal register stores data when the conversion is
in progress. SCLK clocks the data out of this register at
any time after the conversion is complete. After SSTRB
goes high, the next falling clock edge produces the
MSB of the conversion at DOUT, followed by the
remaining bits in MSB-first format (Figure 9). CS does
not need to be held low once a conversion is started.
Pulling CS high prevents data from being clocked into
the MAX146/MAX147 and three-states DOUT, but it
does not adversely affect an internal clock mode
conversion already in progress. When internal clock
mode is selected, SSTRB does not go into a high-
impedance state when CS goes high.
Figure 10 shows the SSTRB timing in internal clock
mode. In this mode, data can be shifted in and out of
the MAX146/MAX147 at clock rates exceeding 2.0MHz
if the minimum acquisition time (tACQ) is kept above
1.5s.
SSTRB
CS
SCLK
DIN
DOUT
14
8
12
18
20
24
START
SEL2 SEL1 SEL0
UNI/
BIP
SGL/
DIF
PD1
PD0
B11
MSB
B10
B9
B2
B1
B0
LSB
FILLED WITH
ZEROS
IDLE
CONVERSION
7.5
s MAX
(SHDN = FLOAT)
2
3
5
6
7
9
10
11
19
21
22
23
tCONV
ACQUISITION
(fSCLK = 2MHz)
IDLE
A/D STATE
1.5
s
Figure 9. Internal Clock Mode Timing
相关PDF资料 |
PDF描述 |
|---|---|
| LLS2G271MELA | CAP ALUM 270UF 400V 20% SNAP |
| 0210490372 | CABLE JUMPER 1.25MM .102M 30POS |
| 380LX332M080K022 | CAP ALUM 3300UF 80V 20% SNAP |
| 0210490371 | CABLE JUMPER 1.25MM .102M 30POS |
| MAX110EVC32-DIP | EVAL KIT FOR MAX110 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX147EVC32-DIP | 功能描述:数据转换 IC 开发工具 MAX147 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX147EVKIT-DIP | 功能描述:数据转换 IC 开发工具 MAX147 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX14800CCM+ | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX14800CCM+T | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX14801CCM+ | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。