- 您现在的位置：买卖IC网 > PDF目录1836 > MAX15021ATI+T (Maxim Integrated Products)IC REG BUCK SYNC ADJ DL 28TQFN PDF资料下载
参数资料
| 型号： | MAX15021ATI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ DL 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 500kHz ~ 4MHz |
| 电流 - 输出： | 2A，4A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
MAX15021
Dual, 4A/2A, 4MHz, Step-Down DC-DC
Regulator with Tracking/Sequencing Capability
Pin Description
PIN
1
2, 7, 8
3, 6
4, 5
9
10
11
12
13, 14, 15,
20, 21, 22
16
17
18
19
23
24
25
26
27
28
—
Maxim Integrated
NAME
SEL
PGND1
LX1
PVIN1
DVDD1
EN1
FB1
COMP1
N.C.
DVDD2
PGND2
LX2
PVIN2
COMP2
FB2
EN2
SGND
AVIN
RT
EP
FUNCTION
Track/Sequence Select Input. Connect SEL to ground to configure the device as a sequencer. Connect
SEL to AVIN for tracking with output 1 as the master. Leave SEL unconnected for tracking with output 2
as the master. Use the output with the higher voltage as the master and the output with the lower voltage
as the slave.
Power Ground Connection for Regulator 1. Connect the negative terminals of the input and output filter
capacitor to PGND1. Connect PGND1 externally to SGND at a single point, typically at the negative
terminal of the input capacitor.
Inductor Connection for Regulator 1. LX1 is the drain connection of the internal high-side p-channel
MOSFET and the drain connection of the internal synchronous n-channel MOSFET for regulator 1.
Input Supply Voltage for Regulator 1. Connect to an external voltage source from 2.5V to 5.5V. Bypass
PVIN1 to PGND1 with a 1μF (min) ceramic capacitor.
Switch Driver Supply for Regulator 1. Connect externally to PVIN1.
Enable Input for Regulator 1. When configured as a sequencer, EN1 must exceed 1.225V (typ) for the
PWM controller to begin regulating output 1. When configured as a tracker, connect EN1 to the center
tap of a resistive divider from the regulator 2 output.
Feedback Regulation Point for Regulator 1. Connect FB1 to the center tap of a resistive divider from the
regulator 1 output to SGND to set the output voltage. The FB1 voltage regulates to 0.6V (typ).
Error-Amplifier Output for Regulator 1. Connect COMP1 to the compensation feedback network.
No Connection. Do not connect.
Switch Driver Supply for Regulator 2. Connect externally to PVIN2.
Power Ground Connection for Regulator 2. Connect the negative terminals of the input and output filter
capacitors to PGND2. Connect PGND2 externally to SGND at a single point, typically at the negative
terminal of the input capacitor.
Inductor Connection for Regulator 2. LX2 is the drain connection of the internal high-side p-channel
MOSFET and the drain connection of the internal synchronous n-channel MOSFET for regulator 2.
Input Supply Voltage for Regulator 2. Connect to an external voltage source from 2.5V to 5.5V. Bypass
PVIN2 to PGND2 with a 1μF (min) ceramic capacitor.
Error-Amplifier Output for Regulator 2. Connect COMP2 to the compensation feedback network.
Feedback Regulation Point for Regulator 2. Connect to the center tap of a resistive divider from the
regulator 2 output to SGND to set the output voltage. The FB2 voltage regulates to 0.6V (typ).
Enable Input for Regulator 2. When configured as a sequencer, EN2 must exceed 1.225V (typ) for the
PWM controller to begin regulating output 2. When configured as a tracker, connect EN2 to the center
tap of a resistive divider from the regulator 1 output.
Signal Ground. Connect SGND to PGND_ at a single point, typically near negative terminal of the input
bypass capacitor.
Input Voltage. Bypass AVIN to SGND with a 100nF (min) ceramic capacitor.
Oscillator Timing Resistor Connection. Connect a 4.2k Ω to 33k Ω resistor from RT to SGND to program
the switching frequency from 500kHz to 4MHz.
Exposed Pad. Connect EP to a large copper plane at SGND potential to improve thermal dissipation. Do
not use as the main SGND connection.
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15023ETG+ | IC REG CTRLR BUCK PWM 24TQFNEP |
| MAX15026CATD+T | IC REG CTRLR BUCK PWM VM 14TDFN |
| MAX15027ATB+T | IC REG LDO ADJ 1A 10-TDFN |
| MAX15030ATB+T | IC REG LDO ADJ .5A 10-TDFN |
| MAX15031ATE+ | IC BOOST CONV/CURRENT MON 16TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15021EVKIT+ | 功能描述:电源管理IC开发工具 MAX15021 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15022ATI+ | 功能描述:直流/直流开关调节器 Dual 4A/2A 4MHz w/Dual LDO Ctlr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15022ATI+T | 功能描述:直流/直流开关调节器 Dual 4A/2A 4MHz w/Dual LDO Ctlr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15022EVKIT+ | 功能描述:电源管理IC开发工具 MAX15022 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15023ETG/V+ | 功能描述:DC/DC 开关控制器 4.5-28V Input Dual Out Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。