- 您现在的位置：买卖IC网 > PDF目录17277 > MAX15026BEVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX15026 PDF资料下载
参数资料
| 型号： | MAX15026BEVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/23页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX15026 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 1.5V |
| 电流 - 输出： | 10A |
| 输入电压： | 5 ~ 16 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX15026B |
MAX15026
Low-Cost, Small, 4.5V to 28V Wide Operating
Range, DC-DC Synchronous Buck Controller
The gain of the error amplifier (GAIN EA ) in midband fre-
quencies is:
5) Place the third pole (f P3 ) at 1/2 the switching fre-
quency and calculate C CF :
GAIN EA = 2 π x f O x C 1 x R F
The total loop gain as the product of the modulator gain
and the error amplifier gain at f O is 1.
C CF =
C F
( 2 π × 0 . 5 × f SW × R F × C F ) ? 1
GAIN MOD × GAIN EA = 1
6) Calculate R 2 as:
× R 1
So:
V IN
V RAMP
×
1
( 2 π × f O ) 2 × C OUT × L OUT
R 2 =
V FB
V OUT ? V FB
MOSFET Selection
× ( 2 π × f × L × C
C I = RAMP O OUT OUT
Solving for C I :
V
V IN × R F
)
The MAX15026 step-down controller drives two external
logic-level n-channel MOSFETs. The key selection
parameters to choose these MOSFETs include:
? On-Resistance (R DS(ON) )
3) Use the second pole (f P2 ) to cancel f ZO when f PO <
f O < f ZO < f SW /2. The frequency response of the
loop gain does not flatten out soon after the 0dB
crossover, and maintains a -20dB/decade slope up
to 1/2 of the switching frequency. This is likely to
occur if the output capacitor is a low-ESR tantalum.
Set f P2 = f ZO .
When using a ceramic capacitor, the capacitor ESR
zero f ZO is likely to be located even above 1/2 the
switching frequency, f PO < f O < f SW /2 < f ZO . In this
case, place the frequency of the second pole (f P2 ) high
enough to not significantly erode the phase margin at
the crossover frequency. For example, set f P2 at 5 x f O
so that the contribution to phase loss at the crossover
frequency f O is only about 11°:
f P2 = 5 x f PO
Once f P2 is known, calculate R I:
? Maximum Drain-to-Source Voltage (V DS(MAX) )
? Minimum Threshold Voltage (V TH(MIN) )
? Total Gate Charge (Q G )
? Reverse Transfer Capacitance (C RSS )
? Power Dissipation
The two n-channel MOSFETs must be a logic-level type
with guaranteed on-resistance specifications at V GS =
4.5V. For maximum efficiency, choose a high-side
MOSFET that has conduction losses equal to the
switching losses at the typical input voltage. Ensure
that the conduction losses at minimum input voltage do
not exceed the MOSFET package thermal limits, or vio-
late the overall thermal budget. Also, ensure that the
conduction losses plus switching losses at the maxi-
mum input voltage do not exceed package ratings or
violate the overall thermal budget. Ensure that the DL
gate driver can drive the low-side MOSFET. In particu-
lar, check that the dv/dt caused by the high-side
R I =
1
2 π × f P 2 × C I
MOSFET turning on does not pull up the low-side
MOSFET gate through the drain-to-gate capacitance
of the low-side MOSFET, which is the most frequent
4) Place the second zero (f Z2 ) at 0.2 x f O or at f PO ,
whichever is lower, and calculate R 1 using the fol-
lowing equation:
cause of cross-conduction problems.
Check power dissipation when using the internal linear
regulator to power the gate drivers. Select MOSFETs
with low gate charge so that V CC can power both dri-
R 1 =
1
2 π × f Z 2 × C I
? R I
vers without overheating the device.
P DRIVE = V CC x Q G_TOTAL x f SW
where Q G_TOTAL is the sum of the gate charges of the
two external MOSFETs.
Maxim Integrated
17
相关PDF资料 |
PDF描述 |
|---|---|
| GEM30DTBN | CONN EDGECARD 60POS R/A .156 SLD |
| 592D337X96R3V2T035 | CAP TANT 330UF 6.3V 10% SMD |
| R1D10-1512 | CONV DC/DC 1W 15VIN +/-12VOUT |
| MCZ33291LEG | IC SWITCH 8X LOSIDE W/SPI 24SOIC |
| FAN3122CMX | IC GATE DVR SGL 9A HS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15026BEVKIT+ | 功能描述:电源管理IC开发工具 MAX15026B Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15026CATD+ | 功能描述:DC/DC 开关控制器 4.5-28V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15026CATD+T | 功能描述:DC/DC 开关控制器 4.5-28V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15026CETD+ | 功能描述:DC/DC 开关控制器 4.5-28V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15026CETD+G1D | 制造商:Maxim Integrated Products 功能描述:LOW-COST, SMALL, 4.5V TO 28V WIDE OPERATING RANGE, DC-DC SYN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。