参数资料
| 型号： | MAX15030ATB+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A 10-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 0.5 V ~ 3.3 V |
| 输入电压： | 1.43 V ~ 3.6 V |
| 电压 - 压降（标准）： | 0.04V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 700mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1412 (CN2011-ZH PDF) |
| 其它名称： | MAX15030ATB+TDKR |
1.425V to 3.6V Input, 500mA Low-Dropout
Regulators with BIAS Input
Internal p-Channel Pass Transistor
The MAX15029/MAX15030 feature a 75m Ω (typ)
p-channel MOSFET pass transistor. Unlike similar
designs using pnp pass transistors, p-channel
MOSFETs require no base drive, reducing quiescent
current. pnp-based regulators also waste considerable
current in dropout when the pass transistor saturates
and uses high base-drive currents under large loads.
The MAX15029/MAX15030 do not suffer from these
problems and consume only 315μA (typ) of quiescent
current under heavy loads, as well as in dropout.
Short-Circuit/
Thermal Fault Protection
The MAX15029/MAX15030 are fully protected from a
short circuit at the output through current-limiting and
thermal-overload circuitry. In the fault condition when
the output is shorted to ground, the output current is
limited to a maximum of 1A. Under these conditions,
Shutdown Mode
The MAX15029/MAX15030 include an enable input. To
shut down the IC, drive EN low. In shutdown mode, the
current drawn by BIAS is less than 2μA. This feature is
extremely useful in an automotive application where the
BIAS input is derived from an always-on LDO expecting
to provide minimal dark current. For normal operation,
drive EN high or connect EN to IN for continuous on
operation. During shutdown, an internal 10k Ω resistor is
connected between OUT and GND.
Applications Information
Programming the Output Voltage
The MAX15029/MAX15030 feature an adjustable output
voltage from 0.5V to V IN using two external resistors
connected as a voltage-divider to FB as shown in
Figure 1. The output voltage is set by the following
equation:
V OUT = V FB ? 1 +
the device quickly heats up. When the junction temper-
ature reaches +165°C (typ), the thermal-overload cir-
cuitry turns off the output, allowing the part to cool
?
?
R1 ?
R 2 ? ?
down. When the junction temperature cools to +150°C
(typ), the output turns back on and reestablishes regu-
lation. Current limiting and thermal protection continue
until the fault is removed. For continuous operation, do
not exceed the absolute maximum junction-tempera-
ture rating of T J = +150°C.
where typically V FB = 0.5V. Choose R2 to be 10k Ω . Or,
to optimize load-transient response for no load to full
load transients, use the resistor-divider as a minimum
load and choose R2 to be 500 Ω . To simplify resistor
selection:
R 1 = R 2 ? OUT
? 1 ?
Soft-Start
The MAX15029/MAX15030 feature a soft-start function
that slowly ramps up the output voltage of the regulator
based on the value of the capacitor (C SS ) connected
from SS to GND. Upon power-up, C SS is charged with
? V
? V FB
?
?
a 5μA (typ) current source through SS. The voltage at
SS is compared to the internal 0.5V reference (V REF ).
The feedback voltage for regulation (V REG ) is the lower
ALWAYS-ON
INPUT
3V TO 5.5V
BIAS
OUT
OUTPUT
of V SS or V REF . As V SS rises, the regulation voltage
(V REG ) rises at the same rate. Once V SS reaches and
rises above V REF , the regulation voltage then tracks the
reference voltage since it is the lower of V SS and V REF .
INPUT
1.425V TO 3.6V
1 μ F
IN
MAX15030
FB
R1
2.2 μ F
The value of C SS determines the length of the soft-start
time, t SS . Use the following formula to determine C SS .
ENABLE
I.C.
R2
C SS = 10 -5 x t SS
where C SS is in farads and t SS is in seconds.
SHUTDOWN
EN
SS
GND
0.1uF
Figure 1. MAX15030 Typical Application Circuit
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15031ATE+ | IC BOOST CONV/CURRENT MON 16TQFN |
| MAX15032ATA+T | IC REG BOOST ADJ 1A 8TDFN-EP |
| MAX15034AAUI+ | IC REG CTRLR BUCK PWM CM 28TSSOP |
| MAX15035ETL+T | IC REG BOOST SYNC 15A 40TQFN |
| MAX15037ATE+ | IC REG BUCK BST SYNC ADJ 16TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15031ATE+ | 功能描述:直流/直流开关转换器 80V 300mW Boost Conv/Current Mtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15031ATE+T | 功能描述:直流/直流开关转换器 80V 300mW Boost Conv/Current Mtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX15031AWE+ | 制造商:Maxim Integrated Products 功能描述:BOOST CNVRTR AND CURRENT MONITOR 16TQFN EP - Rail/Tube |
| MAX15031EVKIT | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX15031 - Bulk |
| MAX15031EVKIT+ | 功能描述:电源管理IC开发工具 MAX15031 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。