- 您现在的位置：买卖IC网 > PDF目录13527 > MAX15037ATE/V+ (Maxim Integrated Products)IC REG BUCK BST SYNC ADJ 16WQFN PDF资料下载
参数资料
| 型号： | MAX15037ATE/V+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/25页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST SYNC ADJ 16WQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 23 V |
| 输入电压： | 4.5 V ~ 23 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 312kHz ~ 2.1MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TQFN-EP（5x5） |
2.2MHz, 3A Buck or Boost Converters
with an Integrated High-Side Switch
( V IN ? V OUT ) × V OUT
Δ I P ? P =
The input ripple comprises mainly of ΔV Q (caused by the
capacitor discharge) and Δ V ESR (caused by the ESR of
the input capacitor). The total voltage ripple is the sum of
Δ V Q and Δ V ESR . Assume the input voltage ripple from
the ESR and the capacitor discharge is equal to 50%
each. The following equations show the ESR and capaci-
where:
V IN × f SW × L
V OUT _ RIPPLE ? Δ V ESR + Δ V Q
tor requirement for a target voltage ripple at the input:
Δ I P-P is the peak-to-peak inductor current as calculated
? Δ I P ? P ?
? I OUT + ?
ESR =
C IN =
Δ V ESR
? 2 ?
I OUT × D ( 1 ? D )
Δ V Q × f SW
above and f SW is the individual converter’s switching
frequency.
The allowable deviation of the output voltage during
fast transient loads also determines the output capaci-
tance and its ESR. The output capacitor supplies the
step load current until the controller responds with a
greater duty cycle. The response time (t RESPONSE )
D = OUT
where
Δ I P ? P =
( V IN ? V OUT ) × V OUT
V IN × f SW × L
V
V IN
and
depends on the closed-loop bandwidth of the convert-
er. The high switching frequency of the MAX15036/
MAX15037 allows for a higher closed-loop bandwidth,
thus reducing t RESPONSE and the output capacitance
requirement. The resistive drop across the output
capacitor’s ESR and the capacitor discharge causes a
voltage droop during a step load. Use a combination of
Δ V ESR
C OUT =
where I OUT is the output current, D is the duty cycle,
and f SW is the switching frequency. Use additional
input capacitance at lower input voltages to avoid pos-
sible undershoot below the UVLO threshold during
transient loading.
Output Capacitor Selection
The allowable output voltage ripple and the maximum
deviation of the output voltage during step load cur-
rents determine the output capacitance and its ESR.
The output ripple comprises of Δ V Q (caused by the
capacitor discharge) and Δ V ESR (caused by the ESR of
the output capacitor). Use low-ESR ceramic or alu-
minum electrolytic capacitors at the output. For alu-
minum electrolytic capacitors, the entire output ripple is
contributed by Δ V ESR . Use the ESR OUT equation to cal-
culate the ESR requirement and choose the capacitor
accordingly. If using ceramic capacitors, assume the
contribution to the output ripple voltage from the ESR
and the capacitor discharge to be equal. The following
equations show the output capacitance and ESR
requirement for a specified output voltage ripple.
low-ESR tantalum and ceramic capacitors for better
transient load and ripple/noise performance. Keep the
maximum output voltage deviation below the tolerable
limits of the electronics being powered. When using a
ceramic capacitor, assume an 80% and 20% contribu-
tion from the output capacitance discharge and the
ESR drop, respectively. Use the following equations to
calculate the required ESR and capacitance value:
ESR OUT =
I STEP
I STEP × t RESPONSE
Δ V Q
where I STEP is the load step and t RESPONSE is the
response time of the controller. The controller response
time depends on the control-loop bandwidth.
Boost Converter
The MAX15036 can be configured for step-up conver-
sion since the internal MOSFET can be used as a low-
side switch. Use the following equations to calculate
the inductor (L MIN ), input capacitor (C IN ), and output
ESR =
Δ V ESR
Δ I P-P
capacitor (C OUT ) when using the converter in boost
operation.
C OUT =
Δ I P-P
8 × Δ V Q × f SW
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| GEC36DRYH-S734 | CONN EDGECARD 72POS DIP .100 SLD |
| GCC15DREF-S734 | CONN EDGECARD 30POS .100 EYELET |
| ECC20DRYN-S734 | CONN EDGECARD 40POS DIP .100 SLD |
| MAX634ESA+T | IC REG INV FLYBK ADJ 0.15A 8SOIC |
| MAX660ESA+T | IC REG SWITCHD CAP DBL INV 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15038ETG+ | 功能描述:直流/直流开关调节器 4A 2MHz Step-Down w/Integrated Switch RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15038ETG+T | 功能描述:直流/直流开关调节器 4A 2MHz Step-Down w/Integrated Switch RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15038EVKIT+ | 功能描述:电源管理IC开发工具 4A 2MHz Step-Down w/Integrated Switch RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15039ETG+ | 功能描述:直流/直流开关调节器 6A 2MHz Step-Down w/Integrated Switch RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX15039ETG+T | 功能描述:直流/直流开关调节器 6A 2MHz Step-Down w/Integrated Switch RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。