- 您现在的位置：买卖IC网 > PDF目录17280 > MAX15041EVKIT+ (Maxim Integrated Products)KIT EVAL MAX15041ETE PDF资料下载
参数资料
| 型号： | MAX15041EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/18页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL MAX15041ETE |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
Low-Cost, 3A, 4.5V to 28V Input, 350kHz, PWM
Step-Down DC-DC Regulator with Internal Switches
R 1 = R 2 × ? OUT ? 1 ?
Programmable Soft-Start (SS)
The MAX15041 utilizes a soft-start feature to slowly ramp
up the regulated output voltage to reduce input inrush
current during startup. Connect a capacitor from SS to
SGND to set the startup time (see the Setting the Soft-
Start Time section for capacitor selection details).
Internal LDO (V DD )
The MAX15041 has an internal 5.1V (typ) LDO. V DD is
externally compensated with a minimum 1μF, low-ESR
ceramic capacitor. The V DD voltage is used to supply
the low-side MOSFET driver, and to supply the internal
control logic. When the input supply (IN) is below 4.5V,
V DD is 50mV (typ) lower than IN. The V DD output cur-
rent limit is 80mA (typ) and an UVLO circuit inhibits
switching when V DD falls below 3.85V (typ).
Error Amplifier
A high-gain error amplifier provides accuracy for the volt-
age feedback loop regulation. Connect the necessary
compensation network between COMP and SGND (see
the Compensation Design Guidelines section). The error-
amplifier transconductance is 1.6mS (typ). COMP clamp
low is set to 0.68V (typ), just below the PWM ramp com-
pensation valley, helping COMP to rapidly return to cor-
rect set point during load and line transients.
PWM Comparator
The PWM comparator compares COMP voltage to the
current-derived ramp waveform (LX current to COMP volt-
age transconductance value is 9A/V, typ.). To avoid insta-
bility due to subharmonic oscillations when the duty cycle
is around 50% or higher, a compensation ramp is added
to the current-derived ramp waveform. The compensation
ramp slope (0.45V x 350kHz) is equivalent to half of the
inductor current down slope in the worst case (load 3A,
current ripple 30% and maximum duty cycle operation of
90%). Compensation ramp valley is set at 0.83V (typ).
Overcurrent Protection
and Hiccup Mode
When the converter output is shorted or the device is
overloaded, the high-side MOSFET current-limit event
(6A, typ) turns off the high-side MOSFET and turns on
the low-side MOSFET. In addition, it discharges the SS
capacitor, C SS for a fixed period of time ( ? T 0 = 70ns,
typ). If the overcurrent condition persists, SS is pulled
below 0.606V and a hiccup event is triggered.
During a hiccup event, high-side and low-side
MOSFETs are kept off, and COMP is pulled low for a
period equal to 16 times the nominal soft-start time
(blanking time). This is obtained by charging SS from 0
to 0.606V with a 5μA (typ) current, and then slowly dis-
charging it back to 0V with a 333nA (typ) current. After
the blanking time has elapsed, the device attempts to
restart. If the overcurrent fault has cleared, the device
resumes normal operation, otherwise a new hiccup
event is triggered (see the Output Short-Circuit
Waveforms in the Typical Operating Characteristics).
Thermal-Shutdown Protection
The MAX15041 contains an internal thermal sensor that
limits the total power dissipation in the device and pro-
tects it in the event of an extended thermal fault condi-
tion. When the die temperature exceeds +155°C (typ),
the thermal sensor shuts down the device, turning off
the DC-DC converter and the LDO regulator to allow
the die to cool. After the die temperature falls by 20°C
(typ), the device restarts, using the soft-start sequence.
Applications Information
Setting the Output Voltage
Connect a resistive divider (R 1 and R 2 , see Figures 1
and 3) from OUT to FB to SGND to set the DC-DC con-
verter output voltage. Choose R 1 and R 2 so that the DC
errors due to the FB input bias current do not affect the
output-voltage precision. With lower value resistors, the
DC error is reduced, but the amount of power consumed
in the resistive divider increases. A typical tradeoff value
for R 2 is 10k ? , but values between 5k ? and 50k ? are
acceptable. Once R 2 is chosen, calculate R 1 using:
? V ?
? V FB ?
where the feedback threshold voltage V FB = 0.606V
(typ).
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| 050R13-102B | CABLE FLAT FLEX 13POS 0.5MM 4" |
| EBC22DREF-S13 | CONN EDGECARD 44POS .100 EXTEND |
| AIRD-06-560K | INDUCTOR 56UH 5.5A 10% |
| RBC20DRYS | CONN EDGECARD 40POS DIP .100 SLD |
| FAN3224CMX | IC GATE DVR LOSIDE DUAL 4A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15041EVKIT+ | 功能描述:电源管理IC开发工具 3A 350kHz Step-Down w/Internal Switch RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15046AAEE+ | 功能描述:DC/DC 开关控制器 40V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15046AAEE+T | 功能描述:DC/DC 开关控制器 40V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15046AEEE+ | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX15046AEEE+T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。