- 您现在的位置：买卖IC网 > PDF目录1836 > MAX1508ZETA+T (Maxim Integrated Products)IC BATT CHARGER LI-ION 8-TDFN PDF资料下载
参数资料
| 型号： | MAX1508ZETA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/11页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.25 V ~ 13 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
Linear Li+ Battery Charger with Integrated Pass FET,
Thermal Regulation, and ACOK in 3mm x 3mm TDFN
Pin Description
PIN
1
2
3
4
5
6
7
8
—
NAME
VL
IN
GND
ISET
EN
EN
ACOK
BATT
CHG
PAD
FUNCTION
Internally Generated Logic Supply for Chip. Bypass VL to GND with a 0.47μF capacitor.
Input Supply Voltage. Bypass IN to GND with a 1μF capacitor to improve line noise and transient rejection.
Ground. Connect GND and exposed pad to a large copper trace for maximum power dissipation.
Charge-Current Program and Fast-Charge Current Monitor. Output current from ISET is 0.958mA per amp of
battery charging current. The charging current is set by connecting a resistor from ISET to GND. Fast-charge
current = 1461V / R ISET ? .
Logic-Level Enable Input (MAX1508/1508Z). Drive EN high to disable charger. Pull EN low or float for normal
operation. EN has an internal 200k ? pulldown resistor.
Logic-Level Enable Input (MAX1508Y). Drive EN low to disable charger. Drive EN high for normal operation.
Input Power-Detection Output. The open-drain ACOK output asserts low when +4.25V < V IN < +7V and V IN -
V BATT > 40mV. ACOK requires an external 100k ? pullup resistor. ACOK is high impedance in shutdown.
Li+ Battery Connection. Bypass BATT to GND with a capacitor of at least 1μF per ampere of charge current.
Charging Indicator, Open-Drain Output. CHG goes low (and can turn on an LED) when charging begins.
CHG is high impedance when the battery current drops below 10% of the fast-charging current, or when EN
is high. Connect a pullup resistor to the μP’s I/O voltage when interfacing with a μP logic input.
Exposed Pad. Connect exposed pad to a large copper trace for maximum power dissipation. The pad is
internally connected to GND.
Detailed Description
The MAX1508 charger uses voltage, current, and ther-
mal-control loops to charge a single Li+ cell and to pro-
tect the battery (Figure 1). When a Li+ battery with a cell
voltage below 2.5V is inserted, the MAX1508 charger
enters the prequalification stage where it precharges that
cell with 10% of the user-programmed fast-charge cur-
rent. There is no prequalification stage for the MAX1508Z
and MAX1508Y in order to allow startup into a load with-
out a battery. The CHG indicator output is driven low
(Figure 2) to indicate entry into the prequalification state.
Once the cell has passed 2.5V, the charger soft-starts
before it enters the fast-charge stage. The fast-charge
current level is programmed through a resistor from ISET
to ground. As the battery voltage approaches 4.2V, the
charging current is reduced. If the battery current drops
to less than 10% of the fast-charging current, the CHG
indicator goes high impedance, signaling the battery is
fully charged. At this point the MAX1508 enters a con-
stant voltage-regulation mode to maintain the battery at
full charge. If, at any point while charging the battery, the
die temperature approaches +100°C, the MAX1508
reduces the charging current so the die temperature
does not exceed the temperature-regulation set point.
The thermal-regulation loop limits the MAX1508 die
temperature to +100°C by reducing the charge current
as necessary (see the Thermal Regulation section).
This feature not only protects the MAX1508 from over-
heating, but also allows higher charge current without
risking damage to the system.
MAX1508/MAX1508Z EN Charger
Enable Input
EN is a logic input (active low) to enable the charger.
Drive EN low, leave floating, or connect to GND to
enable the charger control circuitry. Drive EN high to
disable the charger control circuitry. EN has a 200k ?
internal pulldown resistance.
MAX1508Y EN Charger Enable Input
EN is a logic input (active high) to enable the charger.
Drive EN high to enable the charger control circuitry.
Drive EN low to disable the charger control circuitry.
ACOK Output
Active-Low Output. The open-drain ACOK output
asserts low when +4.25V < V IN < +7V and V IN - V BATT
> 40mV. ACOK requires an external 100k ? pullup
resistor to the system’s logic I/O voltage. ACOK is high
impedance in shutdown.
VL Internal Voltage Regulator
The MAX1508 linear charger contains an internal linear
regulator available on the VL output pin. VL requires a
0.47μF ceramic bypass capacitor to GND. VL is regulat-
ed to 3.3V whenever the input voltage is above 3.5V.
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15101EWL+T | IC REG LDO ADJ 1A 15WLP |
| MAX15102EWL+T | IC REG LDO ADJ 2A 15WLP |
| MAX15103EWL+T | IC REG LDO ADJ 3A 15WLP |
| MAX15109EWP+T | IC REG BUCK SYNC ADJ 8A 20WLP |
| MAX15112EWG+T | IC REG BUCK SYNC ADJ 12A 24WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15090AEVKIT# | 功能描述:电源管理IC开发工具 MAX15090 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15090AEWI+ | 制造商:Maxim Integrated Products 功能描述:2.7V TO 18V, 12A, HOT-SWAP SOLUTION WITH CURRENT REPORT OUTP - Rail/Tube |
| MAX15090AEWI+T | 功能描述:热插拔功率分布 2.7-18V 12A Hotswap w/Internal FET RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX15090EVKIT# | 功能描述:电源管理IC开发工具 MAX15090 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15090EWI+ | 制造商:Maxim Integrated Products 功能描述:2.7V TO 18V, 12A, HOT-SWAP SOLUTION WITH CURRENT REPORT OUTP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。