- 您现在的位置：买卖IC网 > PDF目录1836 > MAX1508ZETA+T (Maxim Integrated Products)IC BATT CHARGER LI-ION 8-TDFN PDF资料下载
参数资料
| 型号： | MAX1508ZETA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.25 V ~ 13 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
Linear Li+ Battery Charger with Integrated Pass FET,
Thermal Regulation, and ACOK in 3mm x 3mm TDFN
Capacitor Selection
Connect a ceramic capacitor from BATT to GND for
proper stability. Use a 1μF X5R ceramic capacitor for
most applications.
Connect a 1μF ceramic capacitor from IN to GND. Use
a larger input bypass capacitor for high input voltages
or high charging currents to reduce supply noise.
Connect a 0.47μF ceramic capacitor from VL to GND.
Thermal Considerations
The MAX1508 is in a thermally enhanced thin DFN pack-
age with exposed paddle. Connect the exposed paddle
of the MAX1508 to a large copper ground plane to pro-
vide a thermal contact between the device and the circuit
board. The exposed paddle transfers heat away from the
device, allowing the MAX1508 to charge the battery with
maximum current, while minimizing the increase in die
temperature.
DC Input Sources
The MAX1508 operates from well-regulated DC
sources. The full-charging input voltage range is 4.25V
to 7V. The device can stand up to 13V on the input
without damage to the IC. If V IN is greater than 7V, then
the MAX1508 stops charging.
An appropriate power supply must provide at least
4.25V when sourcing the desired peak charging cur-
rent. It also must stay below 6.5V when unloaded.
Application Circuits
Stand-Alone Li+ Charger
The MAX1508 provides a complete Li+ charging solu-
tion. The Typical Operating Circuit at the end of the
data sheet shows the MAX1508 as a stand-alone Li+
battery charger. The 2.8k ? resistor connected to ISET
sets a charging current of 520mA. The LED indicates
when either fast-charge or precharge qualification has
begun. When the battery is full, the LED turns off.
Table 1. CHG States
Microprocessor-Interfaced Charger
Figure 3 shows the MAX1508 as a μP-cooperated Li+
battery charger. The MAX1508 and MAX1508Z start
charging the battery when EN is low. The μP can drive
EN high to disable the charger (MAX1508 and
MAX1508Z). The MAX1508’s ACOK output indicates
the presence of a valid AC adapter to the μP. CHG can
be used to detect the charge status of a battery. By
monitoring V ISET , the system can measure the charge
current.
USB-Powered Li+ Charger
The universal serial bus (USB) provides a high-speed
serial communication port as well as power for the
remote device. The MAX1508 can be configured to
charge its battery at the highest current possible from
the host port. Figure 4 shows the MAX1508 as a USB
battery charger. To make the circuit compatible with
either 100mA or 500mA USB ports, the circuit initializes
at 95mA charging current. The microprocessor then
interrogates the host to determine its current capability.
If the host port is capable, the charging current is
increased to 435mA. The 435mA current was chosen to
avoid exceeding the 500mA USB specification.
Layout and Bypassing
Connect a 1μF ceramic input capacitor as close to the
device as possible. Provide a large copper GND plane
to allow the exposed paddle to sink heat away from the
device. Connect the battery to BATT as close to the
device as possible to provide accurate battery voltage
sensing. Make all high-current traces short and wide to
minimize voltage drops. For an example layout, refer to
the MAX1507/MAX1508 evaluation kit layout.
Chip Information
TRANSISTOR COUNT: 1812
PROCESS: BiCMOS
EN
(MAX1508/MAX1508Z)
X
Low
Low
Low
Low
EN
(MAX1508Y)
X
High
High
High
High
V IN
V BATT
4.25V ≤ V IN ≤ 7V
4.25V ≤ V IN ≤ 7V
4.25V ≤ V IN ≤ 7V
>7V
V BATT
V IN
< 2.5V
≥ 2.5V
4.2V
X
I BATT
0
10% of I FAST
I FAST *
10% of I FAST
0
CHG
Hi-Z
Low
Low
Hi-Z
Hi-Z
STATE
Shutdown
Prequalification
Fast Charge
Full Charge
Overvoltage
High Low X X
0
Hi-Z
Disabled
X = Don’t care.
* I FAST is reduced as necessary to maintain the die temperature at +100°C.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15101EWL+T | IC REG LDO ADJ 1A 15WLP |
| MAX15102EWL+T | IC REG LDO ADJ 2A 15WLP |
| MAX15103EWL+T | IC REG LDO ADJ 3A 15WLP |
| MAX15109EWP+T | IC REG BUCK SYNC ADJ 8A 20WLP |
| MAX15112EWG+T | IC REG BUCK SYNC ADJ 12A 24WLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX15090AEVKIT# | 功能描述:电源管理IC开发工具 MAX15090 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15090AEWI+ | 制造商:Maxim Integrated Products 功能描述:2.7V TO 18V, 12A, HOT-SWAP SOLUTION WITH CURRENT REPORT OUTP - Rail/Tube |
| MAX15090AEWI+T | 功能描述:热插拔功率分布 2.7-18V 12A Hotswap w/Internal FET RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX15090EVKIT# | 功能描述:电源管理IC开发工具 MAX15090 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX15090EWI+ | 制造商:Maxim Integrated Products 功能描述:2.7V TO 18V, 12A, HOT-SWAP SOLUTION WITH CURRENT REPORT OUTP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。