参数资料
| 型号： | MAX1515ETG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC REG DDR LV 24-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 应用： | 转换器，DDR |
| 输入电压： | 1.3 V ~ 3.6 V |
| 输出数： | 2 |
| 输出电压： | 0.5 V ~ 2.7 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 管件 |
Low-Voltage, Internal Switch,
Step-Down/DDR Regulator
+3.3V Bias Supply (V CC and V DD )
The MAX1515 requires a 3.3V bias supply for its inter-
nal circuitry. Typically, this 3.3V bias supply is the note-
book’s 95%-efficient, 3.3V system supply. The 3.3V
bias supply must provide V CC (PWM controller) and
V DD (gate-drive and reference buffer power), so the
maximum current drawn is:
I BIAS = I CC + I REFOUT + f SW (Q G(LOW) + Q G(HIGH) )
where I CC is 450μA (typ), f SW is the switching frequen-
cy, and Q G(LOW) and Q G(HIGH) are the internal MOS-
FET total gate charge of approximately 1nC.
The input supply (V IN ) and 3.3V bias inputs (V CC and
V DD ) can be connected together if the input source is a
fixed 3.0V to 3.6V supply. If the 3.3V bias supply pow-
ers up prior to the input supply, the enable signal
( SHDN going from low to high) must be delayed until
Soft-Start Current Limit
Soft-start allows a gradual increase of the internal cur-
rent limit to reduce input surge currents at startup and at
exit from shutdown. A timing capacitor, C SS , placed
from SS to GND sets the rate at which the internal cur-
rent limit is changed. Upon power-up, when the device
comes out of undervoltage lockout (2.6V typ) or after the
SHDN pin is pulled high, a 5μA (typ) constant-current
source charges the soft-start capacitor and the voltage
on SS increases. When the voltage on SS is less than
approximately 0.7V, the current limit is set to zero. As
the voltage increases from 0.7V to approximately 1.8V,
the current limit is adjusted from 0 to the current-limit
threshold (see the Electrical Characteristics ). The volt-
age across the soft-start capacitor changes with time
according to the equation:
the input voltage is present to ensure startup.
Current Limit
V SS =
I SS( SRC) × t
C SS
V OUT × t OFF
2 × L
C SS × 1 . 8 V
SSI LIMIT = × I LIMIT _ P
The MAX1515 provides peak current limiting to protect
the MOSFETs during source/sink overload and short
circuit. During source mode the controller switches the
high-side MOSFET off when the inductor current
exceeds 4.2A. Use the following equation to calculate
the maximum source current:
I SOURCE _ MAX = I LIMIT _ P ?
where I SOURCE_MAX is the maximum source current,
I LIMIT_P is the source inductor current limit (4.2A typ),
and t OFF is the fixed off-time. For typical operating con-
ditions and component selection, this results in a maxi-
mum source current of 3.7A.
In sink mode, the MAX1515 does not issue an off-time
until the inductor current is above -3.2A. Use the follow-
ing equation to calculate the maximum sink current:
where I SS(SRC) is the soft-start source current from the
Electrical Characteristics .
The time when full current limit is available is given by:
t =
I SS ( SRC )
The soft-start current limit varies with the voltage on the
soft-start pin, SS, according to the equation:
V SS ? 0.7 V
V REF
where I LIMIT_P is the positive current threshold from the
Electrical Characteristics . The constant-current source
stops charging once the voltage across the soft-start
capacitor reaches 1.8V (Figure 3).
I SINK _ MAX = I LIMIT _ N +
V OUT t OFF
?
2 ( V IN ? V OUT ) t DLY
2 L
Adjustable Positive Current Limit
The MAX1515 has internal current-limit circuitry that
limits the maximum current through the NMOS to 4.2A.
R SS = ? REF LIMIT + 0 . 7 V ? / I SS ( SRC )
where I SINK_MAX is the maximum sink current, I LIMIT_N
is the sink inductor current limit (-3.0A typ), t DLY is the
current-limit propagation delay of approximately 500ns,
and t OFF is the fixed off-time. For typical operating con-
ditions and component selection, this results in a maxi-
mum sink current of -2.5A.
For applications that require a lower current limit, the
maximum current limit can be reduced by placing a
resistor (R SS ) from SS to GND. The time constant for
the soft-start current limit is R SS x C SS .
? V × I ?
? I LIMIT _ P ?
where I LIMIT is the desired reduced current limit, and
I LIMIT_P and I SS(SRC) are taken from the Electrical
Characteristics .
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1518BETJ+T | IC DC-DC CONV TFT-LCD 32-TQFN |
| MAX1524EUT-T | IC REG CTRLR BST FLYBK SOT23-6 |
| MAX15301ETJ+ | IC REG CTRLR BUCK 32TQFN |
| MAX1531ETJ+T | IC PS CTRLR MULTI-OUTPUT 32TQFN |
| MAX1531ETJ/V+T | IC PS CTRLR MULTI-OUTPUT 32WQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1515ETG+ | 功能描述:直流/直流开关调节器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1515ETG+T | 功能描述:直流/直流开关调节器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1515ETG-T | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1515EVKIT | 制造商:Maxim Integrated Products 功能描述:3A 1MHZ LOW-VOLTAGE INTERNAL SWI - Rail/Tube |
| MAX15166EWE+ | 制造商:Maxim Integrated Products 功能描述:HIGH-EFFICIENCY, 4A, STEP-DOWN DC-DC REGULATOR WITH INTERNAL - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。