- 您现在的位置：买卖IC网 > PDF目录15487 > MAX1541ETL+ (Maxim Integrated Products)IC REG CTRLR DIVIDER PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1541ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/49页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIVIDER PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 620kHz |
| 占空比： | 100% |
| 电源电压： | 2 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
cannot tolerate a negative voltage, place a power
Schottky diode across the output to act as a reverse-
polarity clamp. If the condition that caused the overvolt-
age persists (such as a shorted high-side MOSFET),
the input fuse blows. The MAX1541 ignores OVP faults
on OUT1 when it detects a transition on GATE
(FBLANK enabled). Toggle ON1 or ON2, or cycle V CC
power below 1V to clear the fault latch and restart the
controller.
OVP is disabled when OVP/UVP is connected to REF or
GND (Table 7).
Undervoltage Protection (UVP)
When the output voltage drops below 70% of the nomi-
nal regulation voltage and UVP is enabled (OVP/UVP =
V CC or REF), the controller sets the fault latch and acti-
vates the output discharge sequence (see the
Shutdown and Output Discharge (ON_) section) of both
outputs. When the output voltage drops to 0.3V, the dri-
ver pulls DL high so the synchronous rectifier turns on,
clamping the output to GND. UVP is ignored for at least
10ms (min) after startup (ON_ rising edge), and when
transitions are detected on GATE (MAX1541 only,
FBLANK enabled). Toggle ON1 or ON2, or cycle V CC
power below 1V to clear the fault latch and restart the
controller.
UVP is disabled when OVP/UVP is left open or connect-
ed to GND (Table 7).
Thermal Fault Protection
The MAX1540A/MAX1541 feature a thermal fault-pro-
tection circuit. When the linear regulator is disabled
(LDOON = GND), the controller sets the thermal limit at
+160 ° C. When the linear regulator is enabled (LDOON
= V CC ), the controller sets the thermal limit at +150 ° C to
protect the internal linear regulator from continuous
short-circuit conditions. Once the junction temperature
exceeds the thermal limit, the thermal-protection circuit
activates the fault latch, pulls PGOOD1 and PGOOD2
low, disables the linear regulator, and activates the out-
put discharge sequence of both outputs regardless of
the OVP/UVP setting. Toggle ON1 or ON2, or cycle V CC
power below 1V to reactivate the controller after the
junction temperature cools by 10 ° C.
Output Voltage
Preset Output Voltages
The MAX1540A/MAX1541s ’ Dual Mode operation
allows the selection of common voltages without requir-
ing external components (Figure 10). For the main con-
troller (OUT1) of the MAX1540A, connect FB1 to GND
for a fixed 1.8V output, to V CC for a fixed 1.2V output, or
connect FB1 directly to OUT1 for a fixed 0.7V output.
For the secondary controller (OUT2) of the MAX1540A,
connect FB2 to GND for a fixed 2.5V output, to V CC for
a fixed 1.5V output, or connect FB2 directly to OUT2 for
a fixed 0.7V output. The main controller (OUT1) of the
MAX1541 regulates to the voltage set at REFIN1 (V FB1
= V REFIN1 ) and does not support Dual Mode operation.
For the secondary controller (OUT2) of the MAX1541,
connect FB2 to GND for a fixed 2.5V output, to V CC for
a fixed 1.8V output, or connect FB2 directly to OUT2 for
a fixed 0.7V output. Table 8 shows the output voltage
configuration.
Table 7. Fault Protection and Shutdown Setting Truth Table
OVP/UVP
ON_ DISCHARGE*
UVP PROTECTION
OVP PROTECTION
THERMAL PROTECTION
Yes. Output discharged
V CC
through a 10 Ω resistor,
and DL forced high when
Yes. UVP fault activates Yes. DH pulled low and DL
the discharge sequence. forced high immediately.
Yes. Thermal fault activates
the discharge sequence.
output drops below 0.3V.
Yes. Output discharged
Open
through a 10 Ω resistor,
and DL forced high when
No. UVP disabled.
Yes. DH pulled low and DL
forced high immediately.
Yes. Thermal fault activates
the discharge sequence.
output drops below 0.3V.
REF
GND
No. DL forced low when
shut down.
No. DL forced low when
shut down.
Yes. UVP fault activates
the discharge sequence.
No. UVP disabled.
No. OVP disabled.
No. OVP disabled.
Yes. Thermal fault activates
the discharge sequence.
Yes. Thermal fault activates
the discharge sequence.
* Discharge-mode state latched on power-up.
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| MAX15002ATL+ | IC REG CTRLR BUCK PWM 40-TQFNEP |
| MAX1540AETJ+ | IC REG CTRLR DIVIDER PWM 32-TQFN |
| MAX1956ETI+ | IC REG CTRLR BUCK PWM VM 28-TQFN |
| MAX1639ESE+ | IC REG CTRLR BUCK PWM CM 16-SOIC |
| MAX776ESA+ | IC REG CTRLR INV PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1541ETL+ | 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr w/Saturation Prot RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1541ETL+T | 功能描述:DC/DC 开关控制器 Dual Step-Down Ctlr w/Saturation Prot RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1541ETL-T | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1541EVKIT | 制造商:Maxim Integrated Products 功能描述:DUAL STEP-DOWN CONTROLLERS W. SATURATION PROT - Bulk |
| MAX15425EVKIT# | 功能描述:显示开发工具 Eval Kit for the MAX15425 (Intel CPU Controller) RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
发布紧急采购，3分钟左右您将得到回复。