- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1545ETL+ (Maxim Integrated Products)IC QUICK-PWM DUAL-PHASE 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1545ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/43页 |
| 文件大小： | 0K |
| 描述： | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，Intel Pentium? IV |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 1.85 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Dual-Phase, Quick-PWM Controllers for
Programmable CPU Core Power Supplies
the input voltage due to the typically low duty cycles.
The total load current at the PFM/PWM crossover
threshold (I LOAD(SKIP) ) is approximately:
V DD
C BYP
D BST
I LOAD ( SKIP ) = η TOTAL ? OUT ? ? IN OUT ?
? L ? ? V IN ?
? V K ? ? V -V ?
BST
DH
(R BST )*
C BST
N H
INPUT
(V IN )
where η TOTAL is the number of active phases, and K is
the on-time scale factor (Table 6).
The switching waveforms may appear noisy and asyn-
chronous when light loading activates the pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Varying the inductor
value makes trade-offs between PFM noise and light-load
efficiency. Generally, low inductor values produce a
V DD
LX
DL
PGND
(C NL )*
N L
L
broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the coil
resistance remains fixed) and less output voltage ripple.
Penalties for using higher inductor values include larger
physical size and degraded load-transient response,
especially at low input voltage levels.
Current-Limit Circuit
The current-limit circuit employs a unique “valley” cur-
rent-sensing algorithm that uses current-sense resistors
between the current-sense inputs (C_P to C_N) as the
current-sensing elements. If the current-sense signal of
the selected phase is above the current-limit threshold,
the PWM controller does not initiate a new cycle
(Figure 8) until the inductor current of the selected
phase drops below the valley current-limit threshold.
When either phase trips the current limit, both phases
are effectively current limited since the interleaved con-
troller does not initiate a cycle with either phase.
Since only the valley current is actively limited, the actual
peak current is greater than the current-limit threshold by
an amount equal to the inductor ripple current. Therefore,
the exact current-limit characteristic and maximum load
capability are a function of the current-sense resistance,
inductor value, and battery voltage. When combined with
the undervoltage protection circuit, this current-limit
method is effective in almost every circumstance.
There is also a negative current limit that prevents
excessive reverse inductor currents when V OUT is sink-
ing current. The negative current-limit threshold is set to
approximately 120% of the positive current limit, and
therefore tracks the positive current limit when ILIM is
adjusted. When a phase drops below the negative cur-
rent limit, the controller immediately activates an on-
time pulse—DL turns off, and DH turns on—allowing
the inductor current to remain above the negative cur-
rent threshold.
(R BST )* OPTIONAL—THE RESISTOR LOWERS EMI BY DECREASING THE SWITCHING
NODE RISE TIME.
(CNL)* OPTIONAL—THE CAPACITOR REDUCES LX TO DL CAPACITIVE COUPLING THAT
CAN CAUSE SHOOT-THROUGH CURRENTS.
Figure 9. Optional Gate-Driver Circuitry
The current-limit threshold is adjusted with an external
resistive voltage-divider at ILIM. The current-limit
threshold voltage adjustment range is from 10mV to
75mV. In the adjustable mode, the current-limit thresh-
old voltage is precisely 1/20 the voltage seen at ILIM.
The threshold defaults to 30mV when ILIM is connected
to V CC . The logic threshold for switchover to the 30mV
default value is approximately V CC - 1V.
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the cur-
rent-sense signals seen by the current-sense inputs
(C_P, C_N).
MOSFET Gate Drivers (DH, DL)
The DH and DL drivers are optimized for driving mod-
erately sized, high-side and larger, low-side power
MOSFETs. This is consistent with the low-duty factor
seen in the notebook CPU environment, where a large
V IN - V OUT differential exists. An adaptive dead-time
circuit monitors the DL output and prevents the high-
side FET from turning on until DL is fully off. There must
be a low-resistance, low-inductance path from the DL
driver to the MOSFET gate in order for the adaptive
dead-time circuit to work properly. Otherwise, the
sense circuitry in the Quick-PWM controller interprets
the MOSFET gate as “off” while there is actually charge
still left on the gate. Use very short, wide traces (50 mils
to 100 mils wide if the MOSFET is 1in from the device).
The dead time at the other edge (DH turning off) is
determined by a fixed 35ns internal delay.
The internal pulldown transistor that drives DL low is
robust, with a 0.4 Ω (typ) on-resistance. This helps pre-
vent DL from being pulled up due to capacitive cou-
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
| MAX1565ETJ+ | IC DGTL CAM PWR-SUP 5CH 32TQFN |
| MAX1567ETL+ | IC DGTL CAM PWR-SUP 6CH 40TQFN |
| MAX1572ETC180+ | IC REG BUCK SYNC 1.8V .8A 12TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1545ETL+ | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1545ETL+T | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1545ETL-T | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1546AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1546AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。