- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1545ETL+ (Maxim Integrated Products)IC QUICK-PWM DUAL-PHASE 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1545ETL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 36/43页 |
| 文件大小： | 0K |
| 描述： | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，Intel Pentium? IV |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 1.85 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页
Dual-Phase, Quick-PWM Controllers for
Programmable CPU Core Power Supplies
? V
+ V
? ?
V IN ( MIN ) = η OUTPH ?
?
? 1 ? η OUTPH ?
? ?
? ?
?
Current-Balance Compensation (CCI)
The current-balance compensation capacitor (C CCI )
integrates the difference between the main and sec-
ondary current-sense voltages. The internal compensa-
tion resistor (R CCI = 20k Ω ) improves transient response
by increasing the phase margin. This allows the
dynamics of the current-balance loop to be optimized.
Excessively large capacitor values increase the inte-
gration time constant, resulting in larger current differ-
ences between the phases during transients.
Excessively small capacitor values allow the current
loop to respond cycle-by-cycle but can result in small
DC current variations between the phases. Likewise,
excessively large resistor values can also cause DC
current variations between the phases. Small resistor
values reduce the phase margin, resulting in marginal
stability in the current-balance loop. For most applica-
tions, a 470pF capacitor from CCI to the switching reg-
ulator’s output works well.
Connecting the compensation network to the output
(V OUT ) allows the controller to feed forward the output
voltage signal, especially during transients. To reduce
noise pickup in applications that have a widely distrib-
uted layout, it is sometimes helpful to connect the com-
pensation network to the quiet analog ground rather
than V OUT .
Setting Voltage Positioning
Voltage positioning dynamically lowers the output volt-
age in response to the load current, reducing the
processor ’s power dissipation. When the output is
loaded, an op amp (Figure 5) increases the signal fed
back to the Quick-PWM controller’s feedback input.
The adjustable amplification allows the use of standard,
current-sense resistor values, and significantly reduces
the power dissipated since smaller current-sense resis-
tors can be used. The load-transient response of this
control loop is extremely fast, yet well controlled, so the
amount of voltage change can be accurately confined
within the limits stipulated in the microprocessor power-
supply guidelines.
The voltage-positioned circuit determines the load current
from the voltage across the current-sense resistors
(R SENSE = R CM = R CS ) connected between the inductors
and output capacitors, as shown in Figure 10. The volt-
age drop can be determined by the following equation:
V VPS = A VPS I LOAD R SENSE
for voltage-positioning feedback, and η TOTAL is the total
number of active phases. When the slave controller is
disabled, the current-sense summation maintains the
proper voltage-positioned slope. Select the positive input
summing resistors so R FBS = R F and R A = R B .
Minimum Input Voltage Requirements
and Dropout Performance
The nonadjustable minimum off-time one-shot and the
number of phases restrict the output voltage adjustable
range for continuous-conduction operation. For best
dropout performance, use the slower (200kHz) on-time
settings. When working with low input voltages, the
duty-factor limit must be calculated using worst-case
values for on- and off-times. Manufacturing tolerances
and internal propagation delays introduce an error to
the TON K-factor. This error is greater at higher fre-
quencies (Table 6). Also, keep in mind that transient
response performance of buck regulators operated too
close to dropout is poor, and bulk output capacitance
must often be added (see the V SAG equation in the
Design Procedure section).
The absolute point of dropout is when the inductor cur-
rent ramps down during the minimum off-time ( Δ I DOWN )
as much as it ramps up during the on-time ( Δ I UP ). The
ratio h = Δ I UP / Δ I DOWN is an indicator of the ability to
slew the inductor current higher in response to
increased load, and must always be greater than 1. As
h approaches 1, the absolute minimum dropout point,
the inductor current cannot increase as much during
each switching cycle and V SAG greatly increases
unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but adjusting
this up or down allows trade-offs between V SAG , output
capacitance, and minimum operating voltage. For a
given value of h, the minimum operating voltage can be
calculated as:
? ?
V FB VPS DROP 1
? ? h x t OFF(MIN) ? ?
? K
+ V DROP 2 ? V DROP 1 + V VPS
where η OUTPH is the total number of out-of-phase
switching regulators, V VPS is the voltage-positioning
droop, V DROP1 and V DROP2 are the parasitic voltage
drops in the discharge and charge paths (see the On-
A VPS =
η SUM R F
η TOTAL R B
Time One-Shot section), t OFF(MIN) is from the Electrical
Characteristics , and K is taken from Table 6. The
absolute minimum input voltage is calculated with h = 1.
where η SUM is the number of phases summed together
36
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1551EZK+T | IC BATT CHRGR LI+ 1CELL SOT23-5 |
| MAX1556ETB/V+T | IC REG BUCK SYNC ADJ 1.2A 10TDFN |
| MAX1565ETJ+ | IC DGTL CAM PWR-SUP 5CH 32TQFN |
| MAX1567ETL+ | IC DGTL CAM PWR-SUP 6CH 40TQFN |
| MAX1572ETC180+ | IC REG BUCK SYNC 1.8V .8A 12TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1545ETL+ | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1545ETL+T | 功能描述:电压模式 PWM 控制器 Dual-Phase Quick-PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1545ETL-T | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1546AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1546AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。