- 您现在的位置：买卖IC网 > PDF目录13546 > MAX1572ETC130+ (Maxim Integrated Products)IC REG BUCK SYNC 1.3V .8A 12TQFN PDF资料下载
参数资料
| 型号： | MAX1572ETC130+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 1.3V .8A 12TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.3V |
| 输入电压： | 2.6 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-TQFN-EP（4x4） |
800mA, 2MHz, PWM DC-to-DC
Step-Down Converter with RESET
output and storing energy in the inductor’s magnetic
field. The current-mode feedback system regulates the
peak inductor current as a function of the output voltage
error signal. Since the average inductor current is nearly
the same as the peak inductor current (assuming that
the inductor value is relatively high to minimize ripple
current), the circuit acts as a switch-mode transconduc-
tance amplifier. This pushes the output LC filter pole,
normally found in a voltage-mode PWM, to a higher fre-
quency. To preserve inner-loop stability and eliminate
inductor staircasing, an internal slope-compensation
ramp is summed into the main PWM comparator. During
the second half of the switching cycle (off-time), the
internal high-side P-channel MOSFET turns off and the
internal low-side N-channel MOSFET turns on. Now the
inductor releases the stored energy as its current ramps
down while still providing current to the output. The output
capacitor stores charge when the inductor current
exceeds the load current and discharges when the
inductor current is lower, smoothing the voltage across
the load. Under overload conditions, when the inductor
current exceeds the current limit, the high-side MOSFET
is turned off and the low-side MOSFET remains on for
the remainder of the cycle to let the inductor current
ramp down.
Pulse-Group Mode
Pulse-group mode is used to minimize the supply cur-
rent with a light load. In pulse-group mode, the IC shuts
off most internal circuitry when V OUT is +0.8% above
nominal regulation. When V OUT drops below +0.8% of
the nominal regulation voltage, the IC powers up its cir-
cuits and resumes switching.
Pulse-Skip Mode
Pulse-skip mode is also used to minimize the supply
current with a light load. The difference between pulse-
group and pulse-skip modes is that when V OUT rises
above the +0.8% regulation point, pulse-group mode
stops switching and completely turns off a number of
circuits. Under the same conditions, pulse-skip mode
stops switching but leaves all circuits on. The delay
coming out of pulse-skip mode is shorter than with
Table 2. Recommended Inductors
pulse-group mode. In pulse-skip mode, the output volt-
age ripple is lower, and the load-transient response
faster. However, the quiescent current is higher than in
pulse-group mode.
Forced-PWM Mode
In forced-PWM mode, the MAX1572 operates at a con-
stant 2MHz switching frequency without pulse skipping.
This is desirable in noise-sensitive applications, since the
output ripple is minimized and has a predictable noise
spectrum. Forced-PWM mode requires higher supply
current with light loads due to constant switching.
100% Duty-Cycle Operation
The MAX1572 can operate at 100% duty cycle. In this
state, the high-side P-channel MOSFET is turned on (not
switching). This occurs when the input voltage is close to
the output voltage. The dropout voltage is the voltage
drop due to the output current across the on-resistance
of the internal P-channel MOSFET (R DS(ON)P ) and the
inductor resistance (R L ):
V DROPOUT = I OUT × ( R DS(ON)P + R L )
R DS(ON)P is given in the Electrical Characteristics sec-
tion. R L , for a few recommended inductors, is given in
Table 2.
Load-Transient Response/
Voltage Positioning
The MAX1572 uses voltage positioning that matches
the load regulation to the voltage droop seen during
load transients. In this way, the output voltage does not
overshoot when the load is removed, which results in
the total output-voltage variation being half as wide as
in a conventional design. Figure 2 shows an example of
a voltage-positioned and a nonvoltage-positioned load
transient. Additionally, the MAX1572 uses a wide-band-
width feedback loop to respond more quickly to a load
transient than regulators using conventional integrating
feedback loops.
The load line used to achieve voltage positioning is
shown in Figure 3. This assumes a nominal operating
point of 3.6V input at 300mA load.
MANUFACTURER
Murata
Sumida
TOKO
PART
LQH32CN
CDRH3D16
CDRH2D11
D312F
D412F
VALUE (μH)
2.2
2.2
2.2
2.2
2.2
R L (m ? )
97
50
78
170
140
I SAT (mA)
790
1200
780
1200
1330
SIZE (mm)
2.5 x 3.2 x 2.0
3.8 x 3.8 x 1.8
3.2 x 3.2 x 1.2
3.6 x 3.6 x 1.2
4.8 x 4.8 x 1.2
SHIELDED
No
Yes
Yes
No
No
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| URZ1H220MDD | CAP ALUM 22UF 50V 20% RADIAL |
| VE-J4W-EX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| UWF1E220MCL1GB | CAP ALUM 22UF 25V 20% SMD |
| MAX1763EEE+T | IC REG BST SYNC 3.3V/ADJ 16QSOP |
| UUR1H330MCL6GS | CAP ALUM 33UF 50V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1572ETC130+ | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC130+T | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC130-T | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC150 | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC150+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。