- 您现在的位置：买卖IC网 > PDF目录13546 > MAX1572ETC130+ (Maxim Integrated Products)IC REG BUCK SYNC 1.3V .8A 12TQFN PDF资料下载
参数资料
| 型号： | MAX1572ETC130+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 1.3V .8A 12TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.3V |
| 输入电压： | 2.6 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-TQFN-EP（4x4） |
800mA, 2MHz, PWM DC-to-DC
Step-Down Converter with RESET
+1
NORMAL OPERATION
V OUT
(VOLTAGE POSITIONING)
V OUT
(CONVENTIONAL)
CHANGE IN
OUTPUT 0
VOLTAGE (%)
-1
V IN = 3.6V
V IN = 2.6V
FORCED-PWM
V IN = 5.5V
I OUT
-2
0
200
400
600
800
LOAD CURRENT (mA)
Figure 2. Load Transient Response, With and Without Voltage
Positioning
Soft-Start
Soft-start is used to prevent input-current overshoot dur-
ing startup. For most applications using a 10μF output
capacitor, connect a 1000pF capacitor from SS to GND.
If a larger output capacitor is used, then use the follow-
ing formula to find the value of the soft-start capacitor
needed to prevent input-current overshoot:
C SS = C OUT /10 4
During soft-start, the output voltage rises from 0 to
V OUT(nom) with a time constant equal to C SS times
100k ? (see the Typical Operating Characteristics ).
170ms RESET
RESET is an open-drain output with an internal 14k ?
pullup resistor to OUT. During startup, RESET is held low
until 200ms (typ) after the output voltage reaches 90% of
its nominal regulation voltage. When the output voltage
drops below 90% of its nominal regulation voltage,
RESET pulls low again. See the Typical Operating
Characteristics section for RESET waveforms during
startup and shutdown.
Applications Information
Inductor Selection
A 2.2μH inductor with a saturation current of at least 1A
is recommended for full-load (800mA) applications. For
lower load currents, the inductor current rating may be
reduced. For most applications, use an inductor with a
current rating 1.25 times the maximum required output
Figure 3. Voltage-Positioning Load Line
current. For maximum efficiency, the inductor ’s DC
resistance should be as low as possible. See Table 2
for recommended inductors and manufacturers.
Capacitor Selection
Ceramic 10μF input and output capacitors are recom-
mended for most applications. For output voltages
below 1.5V, output capacitance should be increased to
22μF. For best stability over a wide temperature range,
use capacitors with an X5R or better dielectric.
ABATT Input Filter
In normal applications, an RC filter on ABATT keeps
power-supply noise from entering the IC. Connect a
10 ? resistor between BATT and ABATT and connect a
0.1μF capacitor from ABATT to GND.
PC Board Layout and Routing
Due to fast-switching waveforms and high-current
paths, careful PC board layout is required. An evalua-
tion kit (MAX1572EVKIT) is available to speed design.
When laying out a board, minimize trace lengths
between the IC, the inductor, the input capacitor, and the
output capacitor. Keep these traces short, direct, and
wide. Keep noisy traces, such as the LX node trace,
away from OUT. The input bypass capacitors should be
placed as close to the IC as possible. Connect PGND
and GND directly to the exposed paddle underneath the
IC. The ground connections of the input and output
capacitors should be as close together as possible.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| URZ1H220MDD | CAP ALUM 22UF 50V 20% RADIAL |
| VE-J4W-EX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| UWF1E220MCL1GB | CAP ALUM 22UF 25V 20% SMD |
| MAX1763EEE+T | IC REG BST SYNC 3.3V/ADJ 16QSOP |
| UUR1H330MCL6GS | CAP ALUM 33UF 50V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1572ETC130+ | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC130+T | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC130-T | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC150 | 功能描述:直流/直流开关转换器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1572ETC150+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。