- 您现在的位置：买卖IC网 > PDF目录1837 > MAX1621EEE+T (Maxim Integrated Products)IC TEMP SENSOR W/ALARM 16QSOP PDF资料下载
参数资料
| 型号： | MAX1621EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC TEMP SENSOR W/ALARM 16QSOP |
| 标准包装： | 2,500 |
| 应用： | LCD 显示器 |
| 电流 - 电源： | 150µA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
Digitally Adjustable LCD Bias Supplies
I OUT =
× I PK × V BATT / V OUT
_______________Detailed Description
The MAX1620/MAX1621 are step-up power controllers
that drive an external N-channel FET or NPN transistor
to convert power from a 1.8V to 20V battery to a higher
positive or negative voltage. They are configured as
negative-output, inverting power controllers with one
additional diode and one additional capacitor. Either
configuration ’s output voltage can be adjusted with
external resistors, or digitally adjusted with an internal
digital-to-analog converter (DAC). The MAX1620 uses
pin-defined controls for the DAC, while the MAX1621
communicates with the DAC via the SMBus? interface.
Operating Principle
The MAX1620/MAX1621 operate in discontinuous-
conduction mode (where the inductor current ramps to
zero by the end of each switching cycle) and with a
constant peak current, without requiring a current-
sense resistor. Switch on-time is inversely proportional
to the input voltage V BATT by a microsecond-volt con-
stant, or k-factor, of 20μs-V (e.g., for V BATT = 10V,
on-time = 2μs).
For an ideal boost converter operating in discontinu-
ous-conduction mode (no power losses), output current
is proportional to input voltage and peak inductor current:
1
2
I PK is proportional to on-time (t ON ), which, for these
parts, is determined by the k-factor:
I PK = k-factor / L
2V
Discontinuous conduction is detected by monitoring the
LX node voltage. When the inductor’s energy is com-
pletely delivered, the LX node voltage snaps back to
the BATT voltage. When this crossing is sensed, anoth-
er pulse is issued if the output is still out of regulation.
Positive Output Voltage
To select a positive output voltage, tie the polarity pin
(POL) to V DD and use the typical boost topology shown
in Figure 4. FB regulation voltage is 1.5V. For optimum
stability, V OUT should be greater than 1.1 (V BATT ).
Negative Output Voltage
To select a negative output voltage, tie POL to GND
(Figure 5). In this configuration, the internal error amplifi-
er’s output is inverted to provide the correct feedback
polarity. FB regulation voltage is 0V. D1, D2, C4, and C5
form an inverting charge pump to generate the negative
voltage. This allows application of the positive boost
switching topology to negative output voltages.
The negative output circuit has two possible connec-
tions. In the standard connection, D1’s cathode is con-
nected to BATT. This connection features the best
output ripple performance, but ? V OUT ? must be limited
to no more than 27V - 1.1(V BATT ). If a larger negative
voltage is needed, an alternative connection allows a
maximum negative output of -27V, but with the addition-
al constraint that ? V OUT ? > 1.1V BATT . To use the alter-
native circuit, connect D1’s cathode to ground rather
than BATT (Figure 6). Increase C4 to 2.2 μ F to improve
output ripple performance.
The negative charge pump limits the output current to
the charge transferred each cycle multiplied by the
TO
12V
R1
360k
R8
10k
C3
22 μ F
L1
100 μ H
D3 1N6263 (ANY SCHOTTKY)
U1
C6
100pF
3V
TO
5.5V
R2
100k
C1
0.1 μ F
C2
0.1 μ F
3
5
11
7
4
1
2
6
12
TO REF
BATT
POK
V DD MAX1620
POL MAX1621
SHDN (SUS)
DN (SDA)
UP (SCL)
REF
AGND
LX
DHI
DLO
PGND
DOUT
FB
LCDON
14
16
15
13
10
9
8
R3
300k
D1
MBRS0540
N1
MMFT3055VL
R5
2.2M
R4
300k
C5
22 μ F
R6
56k
R7
56k
Q1
MMBT2907
12.5V
TO
23.5V OUT
VOUTSW
( ) ARE FOR MAX1621.
NOTE: CONNECTIONS TO DIGITAL INPUTS NOT SHOWN.
Figure 4. Typical Operating Circuit—Positive Output
OPTIONAL
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1623EAP | IC REG BUCK SYNC ADJ 3A 20SSOP |
| MAX1626ESA-T | IC REG CTRLR BUCK PWM CM 8-SOIC |
| MAX1631EAI | IC REG CTRLR BUCK PWM CM 28-SSOP |
| MAX1634AEAI+ | IC REG CTRLR BUCK PWM CM 28-SSOP |
| MAX1636EAP+T | IC REG CTRLR BUCK PWM CM 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1621EPE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX1621ESE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX1623EAP | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EA-P | 制造商:Maxim Integrated Products 功能描述: |
| MAX1623EAP+ | 功能描述:直流/直流开关调节器 3A Step-Down w/Synch Rectification RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。