- 您现在的位置：买卖IC网 > PDF目录15134 > MAX1631EAI+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1631EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/29页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 2 |
| 频率 - 最大： | 330kHz |
| 占空比： | 99% |
| 电源电压： | 4.2 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
_________________________________________________Pin Description (continued)
PIN
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
NAME
V DD
(MAX1630/
32/33/35)
SECFB
(MAX1631/
MAX1634)
SYNC
TIME/ON5
GND
REF
SKIP
RESET
FB5
CSL5
CSH5
SEQ
DH5
LX5
BST5
DL5
PGND
VL
V+
SHDN
DL3
BST3
LX3
DH3
RUN/ON3
FUNCTION
Supply Voltage Input for the 12OUT Linear Regulator. Also connects to an internal resistor divider for
secondary winding feedback, and to an 18V overvoltage shunt regulator clamp.
Secondary Winding Feedback Input. Normally connected to a resistor divider from an auxiliary output.
SECFB regulates at V SECFB = 2.5V (see Secondary Feedback Regulation Loop section). Tie to VL if not
used.
Oscillator Synchronization and Frequency Select. Tie to VL for 300kHz operation; tie to GND for 200kHz
operation. Can be driven at 240kHz to 350kHz for external synchronization.
Dual-Purpose Timing Capacitor Pin and ON/ OFF Control Input. See Power-Up Sequencing and
ON/ OFF Controls section.
Low-Noise Analog Ground and Feedback Reference Point
2.5V Reference Voltage Output. Bypass to GND with 1μF minimum.
Logic-Control Input that disables Idle Mode when high. Connect to GND for normal use.
Active-Low Timed Reset Output. RESET swings GND to VL. Goes high after a fixed 32,000 clock-cycle
delay following power-up.
Feedback Input for the 5V SMPS; regulates at FB5 = REF (approx. 2.5V) in adjustable mode. FB5 is a
Dual Mode input that also selects the 5V fixed output voltage setting when tied to GND. Connect FB5 to
a resistor divider for adjustable-output mode.
Current-Sense Input for the 5V SMPS. Also serves as the feedback input in fixed-output mode, and as
the bootstrap supply input when the voltage on CSL5/VL is > 4.5V.
Current-Sense Input for the 5V SMPS. Current-limit level is 100mV referred to CSL5.
Pin-Strap Input that selects the SMPS power-up sequence:
SEQ = GND: 5V before 3.3V, RESET output determined by both outputs
SEQ = REF: Separate ON3/ON5 controls, RESET output determined by 3.3V output
SEQ = VL: 3.3V before 5V, RESET output determined by both outputs
Gate-Drive Output for the 5V, high-side N-channel switch. DH5 is a floating driver output that swings
from LX5 to BST5, riding on the LX5 switching node voltage.
Switching Node (inductor) Connection. Can swing 2V below ground without hazard.
Boost capacitor connection for high-side gate drive (0.1μF)
Gate-Drive Output for the low-side synchronous-rectifier MOSFET. Swings 0V to VL.
Power Ground
5V Internal Linear-Regulator Output. VL is also the supply voltage rail for the chip. After the 5V SMPS
output has reached +4.5V (typical), VL automatically switches to the output voltage via CSL5 for boot-
strapping. Bypass to GND with 4.7μF. VL supplies up to 25mA for external loads.
Battery Voltage Input, +4.2V to +30V. Bypass V+ to PGND close to the IC with a 0.22μF capacitor.
Connects to a linear regulator that powers VL.
Shutdown Control Input, active low. Logic threshold is set at approximately 1V. For automatic start-up,
connect SHDN to V+ through a 220k Ω resistor and bypass SHDN to GND with a 0.01μF capacitor.
Gate-Drive Output for the low-side synchronous-rectifier MOSFET. Swings 0V to VL.
Boost Capacitor Connection for high-side gate drive (0.1μF)
Switching Node (inductor) Connection. Can swing 2V below ground without hazard.
Gate-Drive Output for the 3.3V, high-side N-channel switch. DH3 is a floating driver output that swings
from LX3 to BST3, riding on the LX3 switching node voltage.
ON/ OFF Control Input. See Power-Up Sequencing and ON/ OFF Controls section .
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5067ETH+ | IC REG CTRLR BUCK PWM CM 44-TQFN |
| MAX5041EAI+ | IC REG CTRLR BUCK PWM CM 28-SSOP |
| URS1V332MRD | CAP ALUM 3300UF 35V 20% RADIAL |
| SLPX392M063E3P3 | CAP ALUM 3900UF 63V 20% SNAP |
| SLPX153M025E3P3 | CAP ALUM 15000UF 25V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1631EAI+ | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1631EAI+T | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1631EAI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1631EAI-TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1631EVKIT-SO | 功能描述:DC/DC 开关控制器 Evaluation Kit for the MAX1630 MAX1631 MAX1632 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。