参数资料
型号: MAX1636EAP+
厂商: Maxim Integrated Products
文件页数: 14/23页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 20-SSOP
标准包装: 66
PWM 型: 电流模式,混合
输出数: 1
频率 - 最大: 330kHz
占空比: 99%
电源电压: 3.15 V ~ 30 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 20-SSOP(0.209",5.30mm 宽)
包装: 管件
Low-Voltage, Precision Step-Down
Controller for Portable CPU Power
Table 4. Powering the MAX1636
AVAILABLE
POWER SOURCES
Battery, 3.3V, and 5V
Battery and 5V
Battery and 3.3V
Battery only
V CC
CONNECTS
TO
3.3V
5V
3.3V
VL
V+
CONNECTS
TO
5V
5V
Battery
Battery
VL
CONNECTS
TO
5V
5V
Bypass capacitor only
Bypass capacitor only
COMMENT
Most efficient
Least efficient
REF and VL Supplies and V CC Input
The 1.1V reference (REF) is accurate to ±1% over tem-
perature, making REF useful as a precision system ref-
erence. Bypass REF to GND with a 0.22μF (min)
capacitor. REF can supply up to 50μA for external
loads. Loading REF reduces the main output voltage
slightly because of the reference load-regulation error.
The 5V VL linear-regulator output can be tied to the
system +5V supply in order to obtain gate-drive power
from an efficient source. The two supply pins (V CC and
VL) are independent of each other (no protection
diodes or sequencing requirements), allowing you to
choose the most efficient sources for chip biasing from
among existing system supply voltages without having
to worry about sequencing or latch-up problems
(Table 4).
The V CC input runs the chip if the V CC voltage is
greater than 3.15V. Otherwise, the chip supply is pow-
ered from VL via the internal V CC -VL switchover circuit.
If a system supply between 3.3V and 5V is not avail-
able, tie V CC directly to VL.
In shutdown mode, the VL regulator and reference are
completely turned off. In standby mode, the VL regula-
tor and DL stay alive so that the overvoltage-protection
circuit can operate (Table 5).
Important: Ensure that VL and V CC do not exceed 6V.
Measure VL with the main output fully loaded. If it is
pumped above 5.5V, either excessive boost-diode
capacitance or excessive ripple at V+ is the probable
cause. Use only small-signal diodes for the boost cir-
cuit (10mA to 100mA Schottky or 1N4148 are pre-
ferred) and bypass VL to PGND with a 4.7μF capacitor
directly at the package pins.
Shutdown and Standby Modes
Holding SHDN low puts the IC into its 3μA shutdown
mode. SHDN is a logic input with a threshold of about
1V (the VTH of an internal N-channel MOSFET). For
automatic start-up, tie SHDN to V+.
Standby operation is entered when SHDN = low and
OVP = high (Table 5). In standby mode, the VL regula-
tor stays active, and the DL output is forced high to
provide overvoltage protection by clamping the output
to GND. However, DL is not forced high until the output
sags below V REF , so that the output can be held high
by external keep-alive supplies.
RESET Power-Good Voltage Monitor
The power-good monitor generates a system-reset sig-
nal. The RESET output is an open drain that needs to
be pulled up to the appropriate logic supply. At first
power-up, RESET is held low until output is in regula-
tion. At this point, an internal timer begins counting
oscillator pulses, and RESET continues to be held low
until 32,000 cycles have elapsed. After this timeout
period (107ms at 300kHz or 160ms at 200kHz), the
RESET output is released.
Output Undervoltage Lockout
The output undervoltage-lockout circuit is similar to
foldback current limiting but employs a timer rather
than a variable current limit. The SMPS has an under-
voltage-protection circuit that is activated 6144 clock
cycles after the SMPS is enabled. If the SMPS output is
under 70% of the nominal value, output is latched off
and does not restart until SHDN is toggled or until V+
power is cycled below 1V. Note that undervoltage pro-
tection can make prototype troubleshooting difficult,
since only 20ms or 30ms elapse before the SMPS is
latched off.
The output undervoltage lockout circuit protects
against heavy overloads and shorts to the main SMPS
output. The circuit trips if the output is less than 70% of
the nominal output value any time after the timeout has
expired upon start-up. When the comparator trips, the
output is turned off (the SMPS stops switching). This
state is similar to thermal shutdown and can be exited
by a power-on reset or by a rising edge on SHDN . The
overvoltage crowbar is disabled in output undervoltage
or thermal shutdown modes.
14
______________________________________________________________________________________
相关PDF资料
PDF描述
RYM12DTBD-S664 CONN EDGECARD 24POS R/A .156
MAX770CSA+ IC REG CTRLR BST PWM 8-SOIC
GBM22DTMT-S664 CONN EDGECARD 44POS R/A .156
MAX770CSA IC REG CTRLR BST PWM 8-SOIC
RYM12DTMN-S664 CONN EDGECARD 24POS R/A .156
相关代理商/技术参数
参数描述
MAX1636EAP+ 功能描述:DC/DC 开关控制器 Precision Step-Down for Portable CPU Pwr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1636EAP+T 功能描述:DC/DC 开关控制器 Precision Step-Down for Portable CPU Pwr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1636EAP-T 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1637EEE 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX1637EEE+ 功能描述:DC/DC 开关控制器 Mini Precision Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK