- 您现在的位置：买卖IC网 > PDF目录15038 > MAX1636EAP+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 20-SSOP PDF资料下载
参数资料
| 型号： | MAX1636EAP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/23页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 20-SSOP |
| 标准包装： | 66 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 99% |
| 电源电压： | 3.15 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
Low-Voltage, Precision Step-Down
Controller for Portable CPU Power
Design Procedure
The five predesigned standard application circuits
(Figure 1 and Table 1) contain ready-to-use solutions
for common application needs. Use the following
design procedure to optimize these basic schematics
for different voltage or current requirements. But before
beginning a design, firmly establish the following:
? Maximum input (battery) voltage, V IN(MAX) . This
value should include the worst-case conditions, such
as no-load operation when a battery charger or AC
adapter is connected but no battery is installed.
V IN(MAX) must not exceed 30V.
? Minimum input (battery) voltage, V IN(MIN) . This should
be taken at full load under the lowest battery condi-
tions. If V IN(MIN) is less than 4.5V, use an external cir-
cuit to externally hold VL above the VL undervoltage
lockout threshold. If the minimum input-output differ-
ence is less than 1.5V, the filter capacitance required
to maintain good AC load regulation increases (see
Low-Voltage Operation section).
Inductor Value
The exact inductor value is not critical and can be
freely adjusted to make trade-offs between size, cost,
and efficiency. Lower inductor values minimize size
and cost but reduce efficiency due to higher peak-cur-
rent levels. The smallest inductor is achieved by lower-
ing the inductance until the circuit operates at the
border between continuous and discontinuous mode.
Further reducing the inductor value below this
crossover point results in discontinuous-conduction
operation even at full load. This helps lower output filter
capacitance requirements, but efficiency suffers due to
high I 2 R losses. On the other hand, higher inductor val-
ues mean greater efficiency, but resistive losses due to
extra wire turns eventually exceed the benefit gained
from lower peak-current levels. Also, high inductor val-
ues can affect load-transient response (see the V SAG
equation in the Low-Voltage Operation section). The
equations in this section are for continuous-conduction
operation.
Three key inductor parameters must be specified:
inductance value (L), peak current (I PEAK ), and DC
resistance (R DC ). The following equation includes a
constant, LIR, which is the ratio of inductor peak-to-
peak AC current to DC load current. A higher LIR value
allows smaller inductance but results in higher losses
and higher ripple. A good compromise between size
and losses is a 30% ripple-current to load-current ratio
(LIR = 0.3), which corresponds to a peak inductor cur-
rent 1.15 times higher than the DC load current.
Kool-Mu is a registered trademark of Magnetics, Inc.
L = V OUT (V IN(MAX) - V OUT ) / (V IN(MIN) x f x I OUT x LIR)
where f = switching frequency, normally 200kHz or
300kHz, and I OUT = maximum DC load current. The
peak current can be calculated by:
I PEAK = I LOAD + [V OUT (V IN(MAX) - V OUT ) / (2 x f x L x V IN(MAX) )]
The inductor's DC resistance should be low enough
that R DC x I PEAK < 100mV, as it is a key parameter for
efficiency performance. If a standard, off-the-shelf
inductor is not available, choose a core with an LI 2 rat-
ing greater than L x I PEAK2 and wind it with the largest
diameter wire that fits the winding area. For 300kHz
applications, ferrite-core material is strongly preferred;
for 200kHz applications, Kool-Mu ? (aluminum alloy) or
even powdered iron is acceptable. If light-load efficien-
cy is unimportant (in desktop PC applications, for
example), then low-permeability iron-powder cores may
be acceptable, even at 300kHz. For high-current appli-
cations, shielded-core geometries, such as toroidal or
pot core, help keep noise, EMI, and switching-wave-
form jitter low.
Current-Sense Resistor Value
The current-sense resistor value is calculated accord-
ing to the worst-case, low-current-limit threshold volt-
age (from the Electrical Characteristics table) and the
peak inductor current:
R SENSE = 80mV / I PEAK
Use I PEAK from the second equation in the Inductor
Value section. Use the calculated value of R SENSE to
size the MOSFET switches and specify inductor satura-
tion-current ratings according to the worst-case high-
current-limit threshold voltage:
I PEAK = 120mV / R SENSE
Low-inductance resistors, such as surface-mount metal
film, are recommended.
Input Capacitor Value
Connect low-ESR bulk capacitors directly to the drain
on the high-side MOSFET. The bulk input filter capaci-
tor is usually selected according to input ripple current
requirements and voltage rating, rather than capacitor
value. Electrolytic capacitors with low enough equiva-
lent series resistance (ESR) to meet the ripple-current
requirement invariably have sufficient capacitance val-
ues. Aluminum electrolytic capacitors, such as Sanyo
OS-CON or Nichicon PL, are superior to tantalum
types, which risk power-up surge-current failure, espe-
cially when connecting to robust AC adapters or low-
impedance batteries. RMS input ripple current (I RMS ) is
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RYM12DTBD-S664 | CONN EDGECARD 24POS R/A .156 |
| MAX770CSA+ | IC REG CTRLR BST PWM 8-SOIC |
| GBM22DTMT-S664 | CONN EDGECARD 44POS R/A .156 |
| MAX770CSA | IC REG CTRLR BST PWM 8-SOIC |
| RYM12DTMN-S664 | CONN EDGECARD 24POS R/A .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1636EAP+ | 功能描述:DC/DC 开关控制器 Precision Step-Down for Portable CPU Pwr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1636EAP+T | 功能描述:DC/DC 开关控制器 Precision Step-Down for Portable CPU Pwr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1636EAP-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EEE | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EEE+ | 功能描述:DC/DC 开关控制器 Mini Precision Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。