- 您现在的位置：买卖IC网 > PDF目录1838 > MAX1672EEE-T (Maxim Integrated Products)IC REG BUCK BOOST FIX/ADJ 16QSOP PDF资料下载
参数资料
| 型号： | MAX1672EEE-T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST FIX/ADJ 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 两者兼有 |
| 输出数： | 1 |
| 输出电压： | 3.3V，5V，可调 |
| 输入电压： | 1.8 V ~ 11 V |
| 电流 - 输出： | 300mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-QSOP |
Step-Up/Down DC-DC Converter
in QSOP Package
__________Applications Information
Using a Single, Pushbutton On/Off Switch
A single pushbutton switch can be used to turn the
MAX1672 on and off. As shown in Figure 3, ONA is
pulled low and ONB is pulled high when the part is off.
When the momentary switch is pressed, ONB is pulled
1M ?
ONB
PS
OUT
V DD
low and the regulator turns on. The switch should be on
long enough for the μC to exit reset. The controller
issues a logic high to ONA, which guarantees the part
MAX1672
I/O
μ C
will stay on regardless of the switch state.
To turn off the regulator, press the switch again. The
controller reads the switch status and pulls ONA low.
When the switch is released, ONB goes high, turning
off the MAX1672.
Thermal Overload Protection
Thermal overload protection limits total power dissipa-
tion in the MAX1672. When the junction temperature
exceeds T J = +150°C, the pass transistor turns off,
1M ?
ONA
I/O
allowing the MAX1672 to cool. The pass transistor turns
on again after the IC’s junction temperature cools by
20°C, resulting in a pulsed output during thermal over-
load conditions.
Thermal overload protection is designed to protect the
MAX1672 if fault conditions occur. It is not intended to
be used as an operating mode. Prolonged operation in
thermal shutdown mode may reduce the IC’s reliability.
For continual operation, do not exceed the absolute
maximum junction temperature rating T J = +150°C.
Power Dissipation and Operating Region
The MAX1672’s maximum power dissipation in step-
down mode depends on the thermal resistance of the
case and circuit board, the temperature difference
between the die junction and ambient air, and the air
flow rate. The power dissipated in the device is
P = I OUT (V IN - V OUT ) during step-down operation. The
maximum power dissipation is as follows:
P MAX = (T J - T A )/( θ JB + θ BA )
where (T J - T A ) is the temperature difference between
the MAX1672 die junction and the surrounding air, θ JB
(or θ JC ) is the thermal resistance of the package, and
θ BA is the thermal resistance throughout the printed cir-
cuit board, copper traces, and other materials to the
surrounding air. The MAX1672’s thermal resistance is
120°C/W. See the Typical Operating Characteristics for
the Maximum Output Current vs. Input Voltage Graph.
Figure 3. Momentary Pushbutton On/Off Control
Layout Considerations
Proper PC board layout is essential to minimize noise
due to high inductor current levels and fast switching
waveforms. To maximize output power and efficiency
and minimize output ripple voltage and ground noise,
use the following guidelines when designing your
board:
? Use a ground plane.
? Keep the IC’s GND pin and the ground leads of C1
and C2 (Figure 2) less than 0.2in. (5mm) apart.
? Make all connections to the FB and LX pins as short
as possible.
? Solder the IC ’s GND pin directly to the ground
plane.
Refer to the MAX1672 EV kit for a suggested PC board
layout.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1673ESA | IC REG SWITCHD CAP INV ADJ 8SOIC |
| MAX1675EUA-T | IC REG BOOST SYNC FIX/ADJ 8UMAX |
| MAX1677EEE-T | IC REG BST SYNC 0.35A DL 16QSOP |
| MAX1678EUA+T | IC REG BOOST SYNC 3.3V/ADJ 8UMAX |
| MAX1679EUA+ | IC BATT CHRGR 1CELL LITH 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1672EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX1672 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1673ESA | 功能描述:电荷泵 Regulated 125mA Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MAX1673ESA+ | 功能描述:电荷泵 Regulated 125mA Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MAX1673ESA+T | 功能描述:电荷泵 Regulated 125mA Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MAX1673ESA-T | 功能描述:电荷泵 Regulated 125mA Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。