- 您现在的位置：买卖IC网 > PDF目录20712 > MAX16809ATU+T (Maxim Integrated)IC LED DRVR WT/RGB BCKLT 38-TQFN PDF资料下载
参数资料
| 型号： | MAX16809ATU+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WT/RGB BCKLT 38-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | 开路漏极，PWM，降压（降压），SEPIC，升压（升压） |
| 输出数： | 16 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 20kHz ~ 1MHz |
| 电源电压： | 8 V ~ 26.5 V |
| 输出电压： | 36V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-TQFN（5x7） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
Integrated 16-Channel LED Driver with
Switch-Mode Boost and SEPIC Controller
Pin Description
PIN
1, 31, 32,
36, 38
2
3
NAME
N.C.
FB
COMP
FUNCTION
No Connection. Not internally connected. Leave unconnected.
Error-Amplifier Inverting Input
Error-Amplifier Output
4–11
OUT8–OUT15 LED Driver Outputs. OUT8–OUT15 are open-drain, constant-current-sinking outputs rated for 36V.
12
13
14
15
16, 17
18
19
20
21–28
29
30
33
34
35
37
—
OE
DOUT
SET
V+
PGND
DIN
CLK
LE
OUT0–OUT7
RTCT
CS
AGND
OUT
V CC
REF
EP
Active-Low, Output Enable Input. Drive OE low to PGND to enable the OUT0–OUT15. Drive OE
high to disable OUT0–OUT15.
Serial-Data Output. Data is clocked out of the 16-bit internal shift register to DOUT on CLK’s
rising edge.
LED Current Setting. Connect R SET from SET to PGND to set the LED current.
LED Driver Positive Supply Voltage. Bypass V+ to PGND with a 0.1μF ceramic capacitor.
Power Ground
Serial-Data Input. Data is loaded into the internal 16-bit shift register on CLK’s rising edge.
Serial-Clock Input
Latch-Enable Input. Data is loaded transparently from the internal shift register(s) to the output
latch(es) while LE is high. Data is latched into the output latch(es) on LE’s falling edge, and
retained while LE is low.
LED Driver Outputs. OUT0–OUT7 are open-drain, constant-current-sinking outputs rated for 36V.
PWM Controller Timing Resistor/Capacitor Connection. A resistor R T from RTCT to REF and a
capacitor C T from RTCT to AGND set the oscillator frequency.
PWM Controller Current-Sense Input
Analog Ground
MOSFET Driver Output OUT. Connects to the gate of the external n-channel MOSFET.
Power-Supply Input. Bypass V CC to AGND with a 0.1μF ceramic capacitor or a parallel
combination of a 0.1μF and a higher value ceramic capacitor.
5V Reference Output. Bypass REF to AGND with a 0.1μF ceramic capacitor.
Exposed Paddle. Connect to the ground plane for improved power dissipation. Do not use as the
only ground connection.
Detailed Description
The MAX16809 LED driver includes an internal switch-
mode controller that can be used as a boost or buck-
boost (SEPIC) converter to generate the voltage
necessary to drive the multiple strings of LEDs. This
device incorporates an integrated low-side driver, a
programmable oscillator (20kHz to 1MHz), an error
amplifier, a low-voltage (300mV) current sense for high-
er efficiency, and a 5V reference to power up external
circuitry (see Figures 1a and 1b).
The MAX16809 LED driver includes a 4-wire serial
interface and a current-mode PWM controller to gener-
ate the necessary voltage for driving 16 open-drain,
constant-current-sinking output ports. The driver uses
current-sensing feedback circuitry (not simple current
mirrors) to ensure very small current variations over the
full allowed range of output voltage (see the Typical
Operating Characteristics). The 4-wire serial interface
comprises a 16-bit shift register and a 16-bit transpar-
ent latch. The shift register is written through a clock
input, CLK, and a data input, DIN, and the data propa-
gates to a data output, DOUT. The data output allows
multiple drivers to be cascaded and operated together.
The contents of the 16-bit shift register are loaded into
the transparent latch through a latch-enable input, LE.
The latch is transparent to the shift register outputs
when high and latches the current state on the falling
edge of LE. Each driver output is an open-drain, con-
stant-current sink that should be connected to the
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J3W-CX-F4 | CONVERTER MOD DC/DC 5.5V 75W |
| MAX6979AUG+T | IC LED DRIVER LINEAR 24-TSSOP |
| REC3-0505DRW/H2/C | CONV DC/DC 3W 4.5-9VIN +/-05VOUT |
| A6282ELWTR-T | IC LED DRIVER LINEAR 24-SOIC |
| GBM18DTBN-S189 | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16809EVKIT+ | 功能描述:LED 照明开发工具 MAX16809 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX1680C/D | 功能描述:直流/直流开关转换器 DICE SALES DICE RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1680ESA | 功能描述:直流/直流开关转换器 125mA f-Selct Swtchd Cap Volt Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1680ESA+ | 功能描述:直流/直流开关转换器 125mA f-Selct Swtchd Cap Volt Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1680ESA+T | 功能描述:直流/直流开关转换器 125mA f-Selct Swtchd Cap Volt Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。