- 您现在的位置：买卖IC网 > PDF目录20779 > MAX16831ATJ+ (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 32-TQFN PDF资料下载
参数资料
| 型号： | MAX16831ATJ+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/19页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR HIGH BRIGHT 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 拓扑： | PWM，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED），RGB |
| 频率： | 125kHz ~ 600kHz |
| 电源电压： | 5.5 V ~ 76 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1425 (CN2011-ZH PDF) |
MAX16831
High-Voltage, High-Power LED Driver with
Analog and PWM Dimming Control
Pin Description
8
PIN
1, 24
2
3
4
5
6
7
8
9, 10, 11
12
13
14
15
16, 17
18
19
20
21
22
23
NAME
N.C.
UVEN
REG1
AGND
REF
DIM
RTSYNC
CLKOUT
I.C.
COMP
CS
FB
OV
SGND
DRV
DRI
SNS+
SNS-
QGND
DGT
FUNCTION
No Connection. Not internally connected.
Undervoltage Lockout (UVLO) Threshold/Enable Input. UVEN is a dual-function adjustable UVLO
threshold input with an enable feature. Connect UVEN to V CC through a resistive voltage-divider to
program the UVLO threshold. Connect UVEN directly to V CC to use the 6.0V (max) default UVLO
threshold. Apply a voltage greater than 1.244V to UVEN to enable the device.
5V Regulator Output. REG1 is an internal low-dropout voltage regulator that generates a 5V (V CC >
6V) output voltage and supplies power to internal circuitry. Bypass REG1 to AGND through a 1μF
ceramic capacitor.
Analog Ground
Accurate 3V Buffered Reference Output. Connect REF to DIM through a resistive voltage-divider to
apply a DC voltage for analog-controlled dimming functionality. Leave REF unconnected if unused.
Dimming Control Input. Connect DIM to an external PWM signal for PWM dimming. For analog-
controlled dimming, connect DIM to REF through a resistive voltage-divider. The dimming frequency
is 200Hz under these conditions. Connect DIM to AGND to turn off the LEDs.
SYNC Input/Output. The PWM clock is generated by the RTSYNC oscillator. Connect an external
resistor to RTSYNC to select a clock switching frequency from 125kHz to 600kHz or connect RTSYNC
to an external clock to synchronize the MAX16831 with a master clock signal.
Clock Output. CLKOUT buffers the oscillator/clock. Connect CLKOUT to the SYNC input of another
device to operate the MAX16831 in a multichannel configuration. CLKOUT is a logic output.
Internally Connected. Must be connected to AGND.
Error-Amplifier Output. Connect the compensation network from COMP to FB for stable closed-loop
control. Use low-leakage ceramic capacitors in the feedback network.
Current-Sense Amplifier Output. The current-sense amplifier (CSA) senses the differential voltage
across the load sense resistor, R CS , and generates a voltage, V CS , at CS proportional to the LED
current. Connect the proper compensation resistor from CS to FB.
Error-Amplifier Inverting Input
Overvoltage Protection Input. Connect OV to HI through a resistive voltage-divider to set the
overvoltage limit for the load. When the voltage at OV exceeds the 1.235V (typ) threshold, an
overvoltage fault is generated and the switching MOSFET turns off. The MOSFET is turned on again
when the voltage at OV drops below 1.17V (typ).
Switching Ground. SGND is the ground for non-analog and high-current gate driver circuitry.
Gate Driver Output. Connect DRV to the gate of an external n-channel MOSFET for switching.
Gate Driver Supply Input. Connect DRI to REG2 to power the primary switching MOSFET driver.
Bypass DRI to AGND through a 10μF ceramic capacitor.
Positive Peak Current-Sense Input. Connect SNS+ to the positive side of the switch current-sense
resistor, R SENSE .
Negative Peak Current-Sense Input. Connect SNS- to the negative side of the switch current-sense
resistor, R SENSE .
Analog Ground. Ensure a low-impedance connection between QGND and AGND.
Dimming Gate Driver Output. Connect DGT to the gate of an external n-channel MOSFET for
dimming. DGT is powered by the internal regulator, CLMP, and is referenced to LO.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| GEC05DREI-S93 | CONN EDGECARD 10POS .100 EYELET |
| TAJE108M004RNJ | CAP TANT 1000UF 4V 20% 2917 |
| MSL3162BT-R | IC LED DRVR 16 CHAN PWM 40TQFN |
| EEC08DRYS-S93 | CONN EDGECARD 16POS DIP .100 SLD |
| TAJE108M002RNJ | CAP TANT 1000UF 2.5V 20% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16831ATJ/V+ | 功能描述:LED照明驱动器 w/Analog & PWM Dimming Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16831ATJ/V+T | 功能描述:LED照明驱动器 w/Analog & PWM Dimming Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16831ATJ+ | 功能描述:LED照明驱动器 w/Analog & PWM Dimming Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16831ATJ+T | 功能描述:LED照明驱动器 w/Analog & PWM Dimming Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16831EVKIT+ | 功能描述:LED 照明开发工具 MAX16831 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。