- 您现在的位置：买卖IC网 > PDF目录16770 > MAX17000ETG+ (Maxim Integrated Products)IC PWM CTLR DDR/DDR2/DDR3 24TQFN PDF资料下载
参数资料
| 型号： | MAX17000ETG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/32页 |
| 文件大小： | 0K |
| 描述： | IC PWM CTLR DDR/DDR2/DDR3 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 系列： | Quick-PWM™ |
| 应用： | 存储器，DDR2/DDR3 稳压器 |
| 电流 - 电源： | 2mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MAX17000
Complete DDR2 and DDR3 Memory
Power-Management Solution
Table 4. Fault Protection and Shutdown Setting Truth Table (continued)
OVP
MODE
REACTION/DRIVER STATE
COMMENT
DL and DH immediately pulled low.
Thermal fault
PGOOD1 and PGOOD2 immediately forced low.
VTT and VTTR blocks immediately disabled (high impedance, no
16
discharge on outputs).
Active-fault condition.
General Shutdown
and Fault
Conditions
V CC UVLO
rising edge
V CC POR
rising edge
V CC POR
falling edge
Activate INT_REF once V CC rises above UVLO, and SHDN = high.
Once REFOK is valid (high), initiate the soft-start sequence.
DL remains low until switching/soft-start begins.
DL forced low.
DL = Don ’t care. V CC less than 2VT is not sufficient to turn on the
MOSFETs.
—
—
—
SMPS Overvoltage Protection (OVP)
If the output voltage of the SMPS rises 115% above its
nominal regulation voltage while OVP is enabled (OVP
= V CC ), the controller sets its overvoltage fault latch,
pulls PGOOD1 and PGOOD2 low, and forces DL high.
The VTT and VTTR block shut down immediately, and
the internal 16 Ω discharge MOSFETs on CSL and VTT
are turned on. If the condition that caused the overvolt-
age persists (such as a shorted high-side MOSFET),
the battery fuse blows. Cycle V CC below 1V or toggle
SHDN to clear the overvoltage fault latch and restart the
controller.
OVP is disabled when OVP is connected to AGND
(Table 4). PGOOD1 upper threshold remains active at
115% of nominal regulation voltage even when OVP is
disabled, and the 16 Ω discharge MOSFETs on CSL
and VTT are not enabled in shutdown.
SMPS Undervoltage Protection (UVP)
If the output voltage of the SMPS falls below 85% of its
regulation voltage for more than 200μs (typ), the controller
sets its undervoltage fault latch, pulls PGOOD1 and
PGOOD2 low, and begins soft-shutdown pulsing DL. DH
remains off during the soft-shutdown sequence initiated
by an undervoltage fault. After soft-shutdown has com-
pleted, the MAX17000 forces DL and DH low, and
enables the internal 16 Ω discharge MOSFETs on CSL
and VTT. Cycle V CC below 1V or toggle SHDN to clear
the undervoltage fault latch and restart the controller.
completed, the MAX17000 forces DL and DH low, and
enables the internal 16 Ω discharge MOSFETs on CSL
and VTT. Cycle V CC below 1V or toggle SHDN to clear
the undervoltage fault latch and restart the controller.
Thermal-Fault Protection
The MAX17000 features a thermal-fault protection cir-
cuit. When the junction temperature rises above
+160°C, a thermal sensor activates the fault latch, pulls
PGOOD1 and PGOOD2 low, and shuts down using the
shutdown sequence. Toggle SHDN or cycle V CC power
below V CC POR to reactivate the controller after the
junction temperature cools by 15°C.
Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency and
inductor operating point (ripple-current ratio). The pri-
mary design trade-off lies in choosing a good switching
frequency and inductor operating point, and the follow-
ing four factors dictate the rest of the design:
? Input Voltage Range: The maximum value
(V IN(MAX) ) must accommodate the worst-case input
supply voltage allowed by the notebook ’s AC
adapter voltage. The minimum value (V IN(MIN) )
must account for the lowest input voltage after
drops due to connectors, fuses, and battery selec-
tor switches. If there is a choice at all, lower input
voltages result in better efficiency.
VTT Overvoltage and Undervoltage Protection
If the output voltage of the VTT regulator exceeds
±10% of its regulation voltage for more than 5ms (typ),
the controller sets its fault latch, pulls PGOOD1 and
PGOOD2 low, and begins soft-shutdown pulsing DL.
DH remains off during the soft-shutdown sequence initi-
ated by an undervoltage fault. After soft-shutdown has
Maxim Integrated
?
Maximum Load Current: There are two values to
consider. The peak load current (I LOAD(MAX) ) deter-
mines the instantaneous component stresses and
filtering requirements, and thus drives output
capacitor selection, inductor saturation rating, and
the design of the current-limit circuit. The continu-
ous load current (I LOAD ) determines the thermal
23
相关PDF资料 |
PDF描述 |
|---|---|
| GCM24DCAN-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| EEM08DTBD-S273 | CONN EDGECARD 16POS R/A .156 SLD |
| V24C48C100BF2 | CONVERTER MOD DC/DC 48V 100W |
| ESC06DRYN-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| 562A054-25/86-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17000ETG+ | 功能描述:电压模式 PWM 控制器 DDR2 & DDR3 Memory Power-Mgt RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17000ETG+T | 功能描述:电压模式 PWM 控制器 DDR2 & DDR3 Memory Power-Mgt RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17000EVKIT+ | 功能描述:电源管理IC开发工具 MAX17000 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17003AETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17003AETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。