- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17010ETL+T (Maxim Integrated Products)IC LCD DISPLAY BIAS 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17010ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/17页 |
| 文件大小： | 0K |
| 描述： | IC LCD DISPLAY BIAS 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 50µA |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
Internal-Switch Boost Regulator with Integrated
High-Voltage Level Shifter and Op Amp
Linear Regulator (VL)
The MAX17010 includes an internal 4V linear regulator.
SUP is the input of the linear regulator. The input voltage
range is between 5V and 18V. The output of the linear
regulator (VL) is set to 4V (typ). The regulator powers all
the internal circuitry including the MOSFET gate driver.
Bypass the VL pin to AGND with a 0.22μF or greater
ceramic capacitor. SUP should be directly connected to
the output of the step-up regulator. This feature signifi-
cantly improves the efficiency at low input voltages.
Bootstrapping and Soft-Start
The MAX17010 features bootstrapping operation. In nor-
mal operation, the internal linear regulator supplies
power to the internal circuitry. The input of the linear reg-
ulator (SUP) should be directly connected to the output
of the step-up regulator. The MAX17010 is enabled when
the input voltage at SUP is above 1.4V and the fault latch
is not set. After being enabled, the regulator starts open-
loop switching to generate the supply voltage for the
linear regulator. Step-up switching is inhibited if the step-
up output voltage (V MAIN ) exceeds the voltage on the
SUP input. The internal reference block turns on when the
VL voltage exceeds 2.7V (typ). When the reference volt-
age reaches regulation, the PWM controller and the cur-
rent-limit circuit are enabled and the step-up regulator
enters soft-start. During soft-start, the main step-up regu-
lator directly limits the peak inductor current, allowing
from zero up to the full current-limit value in 128 equal
current steps. The maximum load current is available
after the output voltage reaches regulation (which ter-
minates soft-start), or after the soft-start timer expires in
approximately 3ms. The soft-start routine minimizes the
inrush current and voltage overshoot, and ensures a
well-defined startup behavior.
Fault Protection
During steady-state operation, the MAX17010 monitors
the FB voltage. If the FB voltage does not exceed 1V
(typ), the MAX17010 activates an internal fault timer. If
there is a continuous fault for the fault-timer duration,
the MAX17010 sets the fault latch, shutting down all the
outputs except VL. Once the fault condition is removed,
cycle the input voltage to clear the fault latch and reac-
tivate the device. The fault-detection circuit is disabled
during the soft-start time.
The MAX17010 monitors the SUP voltage for undervolt-
age and overvoltage conditions. If the SUP voltage is
below 1.4V (typ) or above 19V (typ), the MAX17010 dis-
ables the gate driver of the step-up regulator and pre-
vents the internal MOSFET from switching. The SUP
undervoltage and overvoltage conditions do not set the
fault latch.
Op Amps
The MAX17010 has an op amp that is typically used to
drive the LCD backplane (VCOM) and/or the gamma-
correction-divider string. The op amp features ±150mA
output short-circuit current, 45V/μs slew rate, and
12MHz bandwidth. While the op amp is a rail-to-rail
input and output design, its accuracy is significantly
degraded for input voltages within 1V of its supply rails
(SUP and VGND).
Short-Circuit Current Limit
The op amp limits short-circuit current to approximately
±150mA if the output is directly shorted to SUP or to
AGND. If the short-circuit condition persists, the junction
temperature of the IC rises until it reaches the thermal-
shutdown threshold (+160°C typ). Once the junction
temperature reaches the thermal-shutdown threshold, an
internal thermal sensor immediately sets the thermal fault
latch, shutting off all the IC’s outputs except VL. The
device remains inactive until the input voltage is cycled.
Driving Pure Capacitive Load
The op amp is typically used to drive the LCD back-
plane (VCOM) or the gamma-correction-divider string.
The LCD backplane consists of a distributed series
capacitance and resistance, a load that can be easily
driven by the op amp. However, if the op amp is used
in an application with a pure capacitive load, steps
must be taken to ensure stable operation.
As the op amp’s capacitive load increases, the amplifier’s
bandwidth decreases and the gain peaking increases. A
5 Ω to 50 Ω small resistor placed between VCOM and the
capacitive load reduces peaking but also reduces the
gain. An alternative method of reducing peaking is to
place a series RC network (snubber) in parallel with the
capacitive load. The RC network does not continuously
load the output or reduce the gain.
High-Voltage Level-Shifting Scan Driver
The MAX17010 includes eight logic-level to high-volt-
age level-shifting buffers, which can buffer eight logic
inputs (A1–A8) and shift them to a desired level (Y1–Y8)
to drive TFT-LCD row logic. The driver outputs, Y1–Y8,
swing between their power-supply rails, according to
the input-logic level on A1 –A8. The driver output is
GOFF when its respective input is logic low, and GON_
when its respective input is logic high. These eight dri-
ver channels are grouped for different high-level sup-
plies. A1–A6 are supplied from GON1, and A7 and A8
are supplied from GON2. GON1 and GON2 can be tied
together to make A1–A8 use identical supplies.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17014ETM+T | IC PWR SUPPLY MULT-OUTPUT 48TQFN |
| MAX17017GTM+ | IC PWR SUPPLY CONTROLLER 48TQFN |
| MAX17019ATM+T | IC VOLT CTRL QUAD OUT 48-TQFN-EP |
| MAX17020ETJ+ | IC CTLR PWM DUAL STEP DN 32-TQFN |
| MAX17022ETA+T | IC GAUGE 1WIRE UART 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17010EVKIT+ | 功能描述:电源管理IC开发工具 MAX17010 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17014AETM+ | 功能描述:显示驱动器和控制器 Power Supply for LCD TVs RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX17014AETM+T | 功能描述:显示驱动器和控制器 Power Supply for LCD TVs RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX17014ETM+ | 功能描述:其他电源管理 Power Supply for LCD TVs RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX17014ETM+T | 功能描述:显示驱动器和控制器 Power Supply for LCD TVs RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。