- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17014ETM+T (Maxim Integrated Products)IC PWR SUPPLY MULT-OUTPUT 48TQFN PDF资料下载
参数资料
| 型号： | MAX17014ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/33页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY MULT-OUTPUT 48TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | LCD 电视机/监控器 |
| 电流 - 电源： | 8mA |
| 电源电压： | 8 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页
Low-Cost Multiple-Output
Power Supply for LCD TVs
The worst case is I RMS = 0.5 x I OUT , which occurs at
V VIN = 2 x V OUT .
For most applications, ceramic capacitors are used
because of their high ripple current and surge current
capabilities. For optimal circuit long-term reliability,
choose an input capacitor that exhibits less than +10°C
temperature rise at the RMS input current corresponding
to the maximum load current.
Output Capacitor Selection
Since the MAX17014’s step-down regulator is internally
compensated, it is stable with any reasonable amount
of output capacitance. However, the actual capacitance
and equivalent series resistance (ESR) affect the regu-
lator’s output ripple voltage and transient response. The
rest of this section deals with how to determine the out-
put capacitance and ESR needs according to the
ripple-voltage and load-transient requirements.
The output voltage ripple has two components: varia-
response. Calculating the ideal transient response of
the inductor and capacitor, which assumes an ideal
response from the regulator, can ensure that these
components do not degrade the IC’s natural response.
The ideal undershoot and overshoot have two compo-
nents: the voltage steps caused by ESR, and the voltage
sag and soar due to the finite capacitance and the induc-
tor current slew rate. Use the following formulas to check
if the ESR is low enough and the output capacitance is
large enough to prevent excessive soar and sag.
The amplitude of the ESR step is a function of the load
step and the ESR of the output capacitor:
V OUT _ ESR _ STEP = Δ I OUT × R ESR _ OUT
The amplitude of the capacitive sag is a function of the
load step, the output capacitor value, the inductor
value, the input-to-output voltage differential, and the
maximum duty cycle:
2 × C OUT ( VIN ( MIN ) × D MAX OUT
tions in the charge stored in the output capacitor, and
the voltage drop across the capacitor’s ESR caused by
the current into and out of the capacitor:
V OUT _ SAG =
L OUT × ( Δ I OUT ) 2
× V ? V
)
V OUT _ RIPPLE = V OUT _ RIPPLE ( ESR ) + V OUT _ RIPPLE ( C )
V OUT _ RIPPLE ( ESR ) = I OUT _ RIPPLE × R ESR _ OUT
The amplitude of the capacitive soar is a function of the
load step, the output capacitor value, the inductor
value, and the output voltage:
V OUT _ SOAR = OUT OUT
V OUT _ RIPPLE ( C ) =
I OUT _ RIPPLE
8 × C OUT × f SW
L × ( Δ I ) 2
2 × C OUT × V OUT
where I OUT _ RIPPLE is defined in the Inductor Selection
of the Step-Down Regulator section, C OUT is the output
capacitance, and R ESR _ OUT is the ESR of the output
capacitor C OUT . In Figure 1’s circuit, the inductor ripple
current is 0.77A. If the voltage-ripple requirement of
Figure 1’s circuit is ±1% of the 3.3V output, then the
total peak-to-peak ripple voltage should be less than
66mV. Assuming that the ESR ripple and the capacitive
ripple each should be less than 50% of the total peak-
to-peak ripple, then the ESR should be less than 43m Ω
and the output capacitance should be more than 2.43μF
to meet the total ripple requirement. A 22μF capacitor
with ESR (including PCB trace resistance) of 10m Ω is
selected for the standard application circuit in Figure 1,
which easily meets the voltage-ripple requirement.
The step-down regulator’s output capacitor and ESR can
also affect the voltage undershoot and overshoot when
the load steps up and down abruptly. The step-down
regulator’s transient response is typically dominated by
its loop response and the time constant of its internal
integrator. However, excessive inductance or insufficient
output capacitance can degrade the natural transient
Keeping the full-load overshoot and undershoot less
than 3% ensures that the step-down regulator’s natural
integrator response dominates. Given the component
values in the circuit of Figure 1 and assuming a full 2A
step load transient, the voltage step due to capacitor
ESR is negligible. The voltage sag and soar are 44.3mV
and 71.6mV, or a little over 1% and 2%, respectively.
Rectifier Diode
The MAX17014’s high switching frequency demands a
high-speed rectifier. Schottky diodes are recommended
for most applications because of their fast recovery time
and low forward voltage. In general, a 2A Schottky diode
works well in the MAX17014’s step-down regulator.
Step-Up Regulator
Inductor Selection
The inductance value, peak current rating, and series
resistance are factors to consider when selecting the
inductor. These factors influence the converter’s effi-
ciency, maximum output load capability, transient
response time, and output voltage ripple. Physical size
and cost are also important factors to be considered.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17017GTM+ | IC PWR SUPPLY CONTROLLER 48TQFN |
| MAX17019ATM+T | IC VOLT CTRL QUAD OUT 48-TQFN-EP |
| MAX17020ETJ+ | IC CTLR PWM DUAL STEP DN 32-TQFN |
| MAX17022ETA+T | IC GAUGE 1WIRE UART 8TDFN |
| MAX17024ETD+T | IC REG CTRLR DIVIDER PWM 14TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17014EVKIT+ | 功能描述:电源管理IC开发工具 MAX17014 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17015AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015BETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015BETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。