- 您现在的位置：买卖IC网 > PDF目录15533 > MAX17015BETP+ (Maxim Integrated Products)IC BATT CHARGER 1.2MHZ 20-TQFN PDF资料下载
参数资料
| 型号： | MAX17015BETP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER 1.2MHZ 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 包装： | 管件 |
1.2MHz, Low-Cost,
High-Performance Chargers
Operating Conditions
Q1a
RS1
15m ?
SYSTEM LOAD
The MAX17005B/MAX17006B/MAX17015B have the fol-
lowing operating states:
C7
0.1 μ F
C IN
1k ?
ADAPTER
Q1b
?
Adapter Present: When DCIN is greater than 8.7V,
the controller detects the adapter. In this condition,
both the LDO and V AA turn on and battery charging
is allowed:
R6
50k ?
BATTERY
a) Charging: The total MAX17005B/MAX17006B/
MAX17015B quiescent current when charging is
CSSP
CSSN
D1
3mA (max) plus the current required to drive the
MOSFETs.
MAX17015B
BST
C4
0.68 μ F
b) Not Charging: To disable charging, drive ISET
below 26mV. When the adapter is present and
charging is disabled, the total adapter quiescent
current is less than 1.5mA and the total battery
DHI
N1
quiescent current is less than 60μA. The charge
LX
Figure 5. Current-Monitoring Design Battery Discharge
?
pump still operates.
Adapter Absent (Power Fail): When V DCIN is less
than V CSIN + 120mV, the DC-DC converter is in
dropout. The charger detects the dropout condition
and shuts down.
IINP can also be used to monitor battery discharge cur-
rent (see Figure 5). In the MAX17015B, when the adapter
is absent, drive ISET above 2.4V to enable IINP during
battery discharge. When the adapter is reinserted, ISET
The MAX17005B/MAX17006B/MAX17015B allow
charging under the following conditions:
? DCIN > 7.5V, LDO > 4V, V AA > 3.1V
must be released to the correct control level within
300ms.
?
?
V DCIN > V CSIN + 420mV (300mV falling hysteresis)
V ISET > 45mV or PWM detected
AC Adapter Detection
The MAX17005B/MAX17006B/MAX17015B include a
hysteretic comparator that detects the presence of an
AC power adapter. When ACIN is lower than 2.1V, the
open-drain ACOK output becomes high impedance.
Connect a 10k ? pullup resistance between LDO and
ACOK . Use a resistive voltage-divider from the
adapter’s output to the ACIN pin to set the appropriate
detection threshold. Select the resistive voltage-divider
so that the voltage on ACIN does not to exceed its
absolute maximum rating (6V).
LDO Regulator and V AA
An integrated low-dropout (LDO) linear regulator pro-
vides a 5.4V supply derived from DCIN, and delivers
over 40mA of load current. Do not use the LDO to
external loads greater than 10mA. The LDO powers the
gate drivers of the n-channel MOSFETs. See the
MOSFET Drivers section. Bypass LDO to PGND with a
4.7μF ceramic capacitor. V AA is 4.2V reference sup-
plied by DCIN. V AA biases most of the control circuitry,
and should be bypassed to GND with a 1μF or greater
ceramic capacitor.
____________________DC-DC Converter
The MAX17005B/MAX17006B/MAX17015B employ a
synchronous step-down DC-DC converter with an n-
channel high-side MOSFET switch and an n-channel
low-side synchronous rectifier. The charger features a
controlled inductor current-ripple architecture, current-
mode control scheme with cycle-by-cycle current limit.
The controller’s off-time (t OFF ) is adjusted to keep the
high-side MOSFET junction temperature constant. In
this way, the controller switches faster when the high-
side MOSFET has available thermal capacity. This
allows the inductor current ripple and the output-volt-
age ripple to decrease so that smaller and cheaper
components can be used. The controller can also oper-
ate in discontinuous conduction mode for improved
light-load efficiency.
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17006BETP+ | IC BATT CHARGER 1.2MHZ 20-TQFN |
| V48C48C75BL3 | CONVERTER MOD DC/DC 48V 75W |
| MAX8731AETI+T | IC SMBUS LVL2 BATT CHRGR 28TQFN |
| V48C48C75BL2 | CONVERTER MOD DC/DC 48V 75W |
| V48C48C75B3 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17015BETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015BETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17015ETP+TG51 | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。