参数资料
| 型号： | MAX17015EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/24页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX17015 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
1.2MHz Low-Cost,
High-Performance Chargers
c) Minimize other trace lengths in the high-current
paths.
d) Use > 5mm wide traces in the high-current
paths.
e) Connect C IN to high-side MOSFET (10mm max
length).
f) Minimize the LX node (MOSFETs, rectifier cath-
ode, inductor (15mm max length)). Keep LX on
one side of the PCB to reduce EMI radiation.
Ideally, surface-mount power components are flush
against one another with their ground terminals
almost touching. These high-current grounds are
then connected to each other with a wide, filled
zone of top-layer copper, so they do not go through
vias. The resulting top-layer subground plane is
connected to the normal inner-layer ground plane
at the paddle. Other high-current paths should also
be minimized, but focusing primarily on short
ground and current-sense connections eliminates
about 90% of all PCB layout problems.
2) Place the IC and signal components. Keep the
main switching node (LX node) away from sensitive
analog components (current-sense traces and V AA
capacitor). Important: the IC must be no further than
10mm from the current-sense resistors. Quiet con-
nections to V AA and CC should be returned to a sep-
arate ground (GND) island. There is very little current
flowing in these traces, so the ground island need not
be very large. When placed on an inner layer, a siz-
able ground island can help simplify the layout
because the low-current connections can be made
through vias. The ground pad on the backside of the
package should also be connected to this quiet
ground island.
3) Keep the gate drive traces (DHI and DLO) as short
as possible (L < 20mm), and route them away from
the current-sense lines and V AA . These traces
should also be relatively wide (W > 1.25mm).
4) Place ceramic bypass capacitors close to the IC.
The bulk capacitors can be placed further away.
Place the current-sense input filter capacitors under
the part, connected directly to the GND pin.
5) Use a single-point star ground placed directly
below the part at the PGND pin. Connect the power
ground (ground plane) and the quiet ground island
at this location.
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17021EVKIT+ | EVAL KIT FOR MAX17021 |
| MAX1702EVKIT | EVAL KIT FOR MAX1702 |
| MAX17710EVKIT# | RD ENERGY HARVESTING |
| MAX19000EVKIT+ | EVAL KIT MAX19000 |
| MAX19710EVKIT+ | EVAL KIT FOR MAX19710 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17015EVKIT+ | 功能描述:电源管理IC开发工具 MAX17015 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17016ETL+ | 功能描述:DC/DC 开关控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX17016ETL+T | 功能描述:DC/DC 开关控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX17016EVKIT+ | 功能描述:电源管理IC开发工具 MAX17016 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17017DEVKIT+ | 功能描述:电源管理IC开发工具 MAX17017D Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。