- 您现在的位置：买卖IC网 > PDF目录13546 > MAX1701EEE+T (Maxim Integrated Products)IC REG BST SYNC ADJ 0.8A 16QSOP PDF资料下载
参数资料
| 型号： | MAX1701EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SYNC ADJ 0.8A 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.2 V ~ 5.5 V |
| 输入电压： | 0.7 V ~ 5.5 V |
| 频率 - 开关： | 300kHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-QSOP |
1-Cell to 3-Cell, High-Power (1A),
Low-Noise, Step-Up DC-DC Converters
270k
MAX1701
μ C
LX
POUT
ON/OFF
ONB
OUT
V DD
I/O
MAX1700
MAX8865/MAX8866 DUAL OR
MAX8863/MAX8864 SINGLE
0.1 μ F
ONA
270k
I/O
μ C
LOW-DROPOUT LINEAR REGULATORS
RADIO
PA
Figure 10. Momentary Pushbutton On/Off Switch
Output Diode
Use a Schottky diode, such as a 1N5817, MBR0520L, or
equivalent. The Schottky diode carries current during
start-up, and in PFM mode after the synchronous rectifier
turns off. Thus, its current rating only needs to be 500mA.
Connect the diode between LX and P OUT as close to the
IC as possible. Do not use ordinary rectifier diodes since
slow switching speeds and long reverse recovery times
will compromise efficiency and load regulation.
Input and Output Filter Capacitors
Choose input and output filter capacitors that will ser-
vice the input and output peak currents with accept-
able voltage ripple. Choose input capacitors with
working voltage ratings over the maximum input volt-
age, and output capacitors with working voltage ratings
higher than the output.
For full output, two 100μF, 100m ? , low-ESR tantalum out-
put filter capacitors are recommended. For loads below
250mA, a single 100μF output capacitor will suffice. The
input filter capacitor (CIN) reduces peak currents drawn
from the input source and reduces input switching noise.
The input voltage source impedance determines the
required size of the input capacitor. When operating
directly from one or two NiCd cells placed close to the
MAX1700/MAX1701, use a 22μF, low-ESR input filter
capacitor. When operating from a power source placed
farther away, or from higher impedance batteries such as
alkaline or lithium cells, use one or two 100μF, 100m ? ,
low-ESR tantalum capacitors.
Sanyo OS-CON and Panasonic SP/CB-series ceramic
capacitors offer the lowest ESR. Low-ESR tantalum
capacitors are a good choice and generally offer a
good tradeoff between price and performance. Do not
Figure 11. Typical Phone Application
exceed the ripple current ratings of tantalum capaci-
tors. Avoid most aluminum-electrolytic capacitors,
since their ESR is often too high.
Bypass Capacitors
Two ceramic bypass capacitors are required for proper
operation. Bypass REF with a 0.22μF capacitor to GND.
Also connect a 0.22μF ceramic capacitor from OUT to
GND. Each should be placed as close to their respec-
tive pins as possible, within 0.2in. (5mm) of the DC-DC
converter IC. See Table 4 for suggested suppliers.
__________Applications Information
Push-On/Push-Off Control
A momentary pushbutton switch can be used to turn
the MAX1700/MAX1701 on and off. In Figure 10, ONA
is pulled low and ONB is pulled high when the part is
off. When the momentary switch is pressed, ONB is
pulled low and the regulator turns on. The switch must
be pressed long enough for the microcontroller to exit
reset (200ms) and drive ONA high. A small capacitor is
added to help debounce the switch. The controller
issues a logic high to ONA, which holds the part on
regardless of the switch state. To turn the regulator off,
press the switch again, allowing the controller to read
the switch status and pull ONA low. When the switch is
released, ONB is pulled high.
Use in a Typical Wireless
Phone Application
The MAX1700/MAX1701 are ideal for use in digital
cordless and PCS phones. The power amplifier (PA) is
connected directly to the boost-converter output for
maximum voltage swing (Figure 11). Low-dropout linear
regulators are used for post-regulation to generate
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17094ETM+ | IC REG BOOST ADJ 1A 7OUT 48TQFN |
| MAX16904SAUE50/V+T | IC REG BUCK SYNC 5V 0.6A 16TSSOP |
| MAX6734AKAVHD3+T | IC SUPERVISOR MPU W/WD SOT23-8 |
| MAX16904SAUE33/V+T | IC REG BUCK SYNC 3.3V 16TSSOP |
| MAX16904RAUE50/V+T | IC REG BUCK SYNC 5V 0.6A 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1701EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX1700 MAX1701 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX17020ETJ+ | 功能描述:电压模式 PWM 控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17020ETJ+T | 功能描述:电压模式 PWM 控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17020EVKIT+ | 制造商:Maxim Integrated Products 功能描述:SINGLE QUICK-PWM STEP-DOWN CONTROLL - Boxed Product (Development Kits) |
| MAX17021EVKIT+ | 功能描述:电源管理IC开发工具 MAX17021 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。