参数资料
型号: MAX1701EEE+T
厂商: Maxim Integrated Products
文件页数: 5/16页
文件大小: 0K
描述: IC REG BST SYNC ADJ 0.8A 16QSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
类型: 升压(升压)
输出类型: 可调式
输出数: 1
输出电压: 2.2 V ~ 5.5 V
输入电压: 0.7 V ~ 5.5 V
频率 - 开关: 300kHz
电流 - 输出: 800mA
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-SSOP(0.154",3.90mm 宽)
包装: 带卷 (TR)
供应商设备封装: 16-QSOP
1-Cell to 3-Cell, High-Power (1A),
Low-Noise, Step-Up DC-DC Converters
ELECTRICAL CHARACTERISTICS (continued)
(CLK/SEL = ONA = ONB = FB = PGND = GND, OUT = POUT, V OUT = 3.6V, MAX1701: AIN = LBN = GND, LBP = REF,
T A = -40°C to +85°C, unless otherwise noted.) (Note 8)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LOGIC AND CONTROL INPUTS
Input Low Voltage (Note 7)
Input High Voltage (Note 7)
Input High Voltage (Note 7)
1.2V < V OUT < 5.5V, ONA and ONB
2.5V < V OUT < 5.5V, CLK/SEL
1.2V < V OUT < 5.5V, ONA and ONB
2.5V < V OUT < 5.5V, CLK/SEL
0.8V OUT
0.8V OUT
0.2V OUT
0.2V OUT
V
V
Logic Input Current
Internal Oscillator Frequency
Oscillator Maximum Duty Cycle
External Clock Frequency
Range
ONA, ONB , and CLK/SEL
CLK/SEL = OUT
-1
260
80
200
1
340
92
400
μA
kHz
%
kHz
Note 1: Operating voltage. Since the regulator is bootstrapped to the output, once started it will operate down to 0.7V input.
Note 2: Start-up is tested with the circuit of Figure 2.
Note 3: In low-power mode (CLK/SEL = GND), the output voltage regulates 1% higher than low-noise mode (CLK/SEL = OUT or
synchronized).
Note 4: The regulator is in start-up mode until this voltage is reached. Do not apply full load current.
Note 5: Load regulation is measured from no-load to full load where full load is determined by the N-channel switch current limit.
Note 6: Supply current from the 3.30V output is measured between the 3.30V output and the OUT pin. This current correlates
directly to the actual battery supply current, but is reduced in value according to the step-up ratio and efficiency. Set V OUT
= 3.6V to keep the internal switch open when measuring the current into the device.
Note 7: ONA and ONB have hysteresis of approximately 0.15xV OUT .
Note 8: Specifications to -40°C are guaranteed by design and not production tested.
Typical Operating Characteristics
(T A = +25°C, unless otherwise noted.)
MAX1701
100
EFFICIENCY vs. LOAD CURRENT
(V OUT = 3.3V)
100
EFFICIENCY vs. LOAD CURRENT
(V OUT = 5V)
7.0
SHUTDOWN CURRENT
vs. INPUT VOLTAGE (V)
90
80
V IN = 2.4V
90
80
V IN = 3.6V
V IN = 2.4V
6.0
5.0
T = 25°C
70
60
50
V IN = 0.9V
V IN = 1.2V
PFM
PWM
70
60
50
40
V IN = 1.2V
PFM
PWM
4.0
3.0
2.0
1.0
T = 85°C
T = -40°C
40
0.1
1
10
100
1000
30
0.1
1
10
100
1000
0
0
1
2
3
4
5
6
LOAD CURRENT (mA)
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
_______________________________________________________________________________________
5
相关PDF资料
PDF描述
MAX17094ETM+ IC REG BOOST ADJ 1A 7OUT 48TQFN
MAX16904SAUE50/V+T IC REG BUCK SYNC 5V 0.6A 16TSSOP
MAX6734AKAVHD3+T IC SUPERVISOR MPU W/WD SOT23-8
MAX16904SAUE33/V+T IC REG BUCK SYNC 3.3V 16TSSOP
MAX16904RAUE50/V+T IC REG BUCK SYNC 5V 0.6A 16TSSOP
相关代理商/技术参数
参数描述
MAX1701EVKIT 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX1700 MAX1701 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
MAX17020ETJ+ 功能描述:电压模式 PWM 控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX17020ETJ+T 功能描述:电压模式 PWM 控制器 Quick-PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
MAX17020EVKIT+ 制造商:Maxim Integrated Products 功能描述:SINGLE QUICK-PWM STEP-DOWN CONTROLL - Boxed Product (Development Kits)
MAX17021EVKIT+ 功能描述:电源管理IC开发工具 MAX17021 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V