- 您现在的位置：买卖IC网 > PDF目录5135 > MAX17021GTL+ (Maxim Integrated Products)IC CTLR PWM DUAL IMVP-6+ 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17021GTL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 28/48页 |
| 文件大小： | 0K |
| 描述： | IC CTLR PWM DUAL IMVP-6+ 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器， Intel IMVP-6+，IMVP-6.5? |
| 输入电压： | 4.5 V ~ 5.5 V |
| 输出数： | 1 |
| 输出电压： | 0.013 V ~ 1.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Dual-Phase, Quick-PWM Controllers for
IMVP-6+/IMVP-6.5 CPU Core Power Supplies
Differential Remote Sense
The MAX17021/MAX17082/MAX17482 include differen-
tial, remote-sense inputs to eliminate the effects of volt-
age drops along the PCB traces and through the
processor’s power pins. The feedback-sense node con-
nects to the voltage-positioning resistor (R FB ). The
ground-sense (GNDS) input connects to an amplifier
that adds an offset directly to the target voltage, effec-
tively adjusting the output voltage to counteract the volt-
age drop in the ground path. Connect the
voltage-positioning resistor (R FB ), and ground-sense
(GNDS) input directly to the processor’s remote-sense
outputs, as shown in Figure 1.
Integrator Amplifier
An integrator amplifier forces the DC average of the FB
voltage to equal the target voltage. This transconduc-
tance amplifier integrates the feedback voltage and pro-
vides a fine adjustment to the regulation voltage (Figure
3), allowing accurate DC output-voltage regulation
regardless of the output ripple voltage. The integrator
amplifier has the ability to shift the output voltage by
±100mV (typ). The differential input-voltage range is at
least ±60mV total, including DC offset and AC ripple.
The MAX17021/MAX17082/MAX17482 disable the inte-
grator by connecting the amplifier inputs together at the
beginning of all VID transitions done in pulse-skipping
mode (DPRSLPVR = high). The integrator remains dis-
abled until 20μs after the transition is completed (the
internal target settles) and the output is in regulation
(edge detected on the error comparator).
Transient-Overlap Operation
When a transient occurs, the response time of the con-
troller depends on how quickly it can slew the inductor
current. Multiphase controllers that remain 180° out-of-
phase when a transient occurs actually respond slower
than an equivalent single-phase controller. To provide
fast-transient response, the MAX17021/MAX17082/
MAX17482 support a phase-overlap mode, which
allows the dual regulators to operate in-phase when
heavy load transients are detected, effectively reducing
the response time. After either high-side MOSFET turns
off, if the output voltage does not exceed the regulation
voltage when the minimum off-time expires, the con-
troller simultaneously turns on both high-side MOSFETs
during the next on-time cycle. This maximizes the total
inductor current slew rate. The phases remain over-
lapped until the output voltage exceeds the regulation
voltage after the minimum off-time expires.
After the phase-overlap mode ends, the controller automat-
ically begins with the opposite phase. For example, if the
secondary phase provided the last on-time pulse before
overlap operation began, the controller starts switching
with the main phase when overlap operation ends. Table 3
is the operating mode truth table.
Nominal Output-Voltage Selection
The nominal no-load output voltage (V TARGET ) is
defined by the selected voltage reference (VID DAC)
plus the remote ground-sense adjustment (V GNDS ) as
defined in the following equation:
V TARGET = V FB = V DAC + V GNDS
where V DAC is the selected VID voltage. On startup, the
MAX17021/MAX17082/MAX17482 slew the target volt-
age from ground to the preset boot voltage.
DAC Inputs (D0–D6)
The digital-to-analog converter (DAC) programs the
output voltage using the D0–D6 inputs. D0–D6 are low-
voltage (1.0V) logic inputs, designed to interface direct-
ly with the CPU. Do not leave D0–D6 unconnected.
Changing D0–D6 initiates a transition to a new output-
voltage level. Change D0–D6 together, avoiding greater
than 20ns skew between bits. Otherwise, incorrect DAC
readings might cause a partial transition to the wrong
voltage level followed by the intended transition to the
correct voltage level, lengthening the overall transition
time. The available DAC codes and resulting output
voltages are compatible with the IMVP-6/IMVP-6+ and
IMVP-6.5 (Table 4) specifications.
28
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ABB24DHFN | CONN EDGECARD 48POS .050 SMD |
| 450VXG560MEFCSN35X50 | CAP ALUM 560UF 450V 20% SNAP-IN |
| MAX17004ETJ+T | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 63MXG15000MEFCSN35X50 | CAP ALUM 15000UF 63V 20% SNAP-IN |
| ACB24DHFD | CONN EDGECARD 48POS .050 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17021GTL+ | 功能描述:电压模式 PWM 控制器 Dual-Phase, Quick-Pw M Controllers For Im RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17021GTL+T | 功能描述:电压模式 PWM 控制器 Dual-Phase, Quick-Pw M Controllers For Im RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17022ETA+T | 功能描述:电池管理 Fuel Guage For Portable Devices RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17022EVKIT+ | 功能描述:电源管理IC开发工具 MAX17022 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17023BAUI/V+ | 制造商:Maxim Integrated Products 功能描述:DUAL STEP-DOWN CONTROLLER - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。