- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17030GTL+ (Maxim Integrated Products)IC CTRLR VID QUICK-PWM 40-TQFN PDF资料下载
参数资料
| 型号： | MAX17030GTL+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/39页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR VID QUICK-PWM 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，Intel IMVP-6.5? SV，XE |
| 输入电压： | 7 V ~ 26 V |
| 输出数： | 1 |
| 输出电压： | 0.013 V ~ 1.5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
1/2/3-Phase Quick-PWM
IMVP-6.5 VID Controllers
Pin Description
PIN
1
2
3
4
5
6
7
8
NAME
CSN3
CSP3
THRM
IMON
ILIM
TIME
V CC
FB
FUNCTION
Negative Input of the Output Current Sense of Phase 3. This pin should be connected to the
negative side of the output current-sensing resistor or the filtering capacitor if the DC resistance of
the output inductor is utilized for current sensing.
Positive Input of the Output Current Sense of Phase 3. This pin should be connected to the positive
side of the output current-sensing resistor or the filtering capacitor if the DC resistance of the
output inductor is utilized for current sensing.
To disable phase 3, connect CSP3 to V CC and CSN3 to GND.
Input of Internal Comparator. Connect the output of a resistor- and thermistor-divider (between V CC
and GND) to THRM. Select the components such that the voltage at THRM falls below 1.5V (30% of
V CC ) at the desired high temperature.
Current Monitor Output Pin. The output current at this pin is:
I IMON = G M(IMON) x
V(CSP_,CSN_)
where G M(IMON) = 1.6mS typical and
denotes summation over all enabled phases.
An external resistor R IMON between IMON and GNDS sets the current-monitor output voltage:
V IMON = I LOAD x R SENSE x G M(IMON) x R IMON
where R SENSE is the value of the effective current-sense resistance.
Choose R IMON such that V IMON does not exceed 900mV at the maximum expected load current I MAX .
IMON is high impedance when the MAX17030/MAX17036 are in shutdown.
Current-Limit Adjust Input. The valley positive current-limit threshold voltages at V(CSP_,CSN_) are
precisely 1/10 the differential voltage V(TIME,ILIM) over a 0.1V to 0.5V range of V(TIME,ILIM). The
valley negative current-limit thresholds are typically -125% of the corresponding valley positive
current-limit thresholds. Connect ILIM to V CC to get the default current-limit threshold setting of
22.5mV typ.
Slew-Rate Adjustment Pin. The total resistance R TIME from TIME to GND sets the internal slew rate:
Slew rate = (12.5mV/μs) x (71.5k /R TIME )
where R TIME is between 35.7k
and 178k .
This “normal” slew rate applies to transitions into and out of the low-power pulse-skipping modes
and to the transition from boot mode to VID. The slew rate for startup and for entering shutdown is
always 1/4 of normal. If the VID DAC inputs are clocked, the slew rate for all other VID transitions
is set by the rate at which they are clocked, up to a maximum slew rate equal to the normal slew
rate defined above.
Controller Supply Voltage. Connect to a 4.5V to 5.5V source. Bypass to GND with 1 μF minimum.
Feedback Voltage Input. The voltage at the FB pin is compared with the slew-rate-controlled target
voltage by the error comparator (fast regulation loop), as well as by the internal voltage integrator
(slow, accurate regulation loop). Having sufficient ripple signal at FB that is in phase with the sum
of the inductor currents is essential for cycle-by-cycle stability.
The external connections and compensation at FB depend on the desired DC and transient (AC)
droop values. If DC droop = AC droop, then short FB to FBAC. To disable DC droop, connect FB to the
remote-sensed output voltage through a resistor R and feed forward the FBAC ripple to FB through
capacitor C, where the R x C time constant should be at least 3x the switching period per phase.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1703ESE | IC REG BOOST SYNC 5V/ADJ 16SOIC |
| MAX17041G+T | IC 2-WIRE FG W/MODEL GAUGE |
| MAX17044G+T | IC FUEL GAUGE LI-ION 8-TDFN |
| MAX17049G+ | IC FUEL/GAS GAUGE LI-ION 8TDFN |
| MAX17062ETB+T | IC TFT-LCD DC/DC CONV 10-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17030GTL+ | 功能描述:电压模式 PWM 控制器 1/2/3-Phase PWM IMVP-6.5 VID Ctlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17030GTL+T | 功能描述:电压模式 PWM 控制器 1/2/3-Phase PWM IMVP-6.5 VID Ctlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17031ETG+ | 功能描述:电压模式 PWM 控制器 Dual PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17031ETG+T | 功能描述:电压模式 PWM 控制器 Dual PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17033GTL+ | 功能描述:电压模式 PWM 控制器 Dual PWM Step-Down Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。