- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17067EUA+T (Maxim Integrated Products)IC REG BOOST ADJ 0.3A 8UMAX PDF资料下载
参数资料
| 型号： | MAX17067EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 0.3A 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.25 V ~ 18 V |
| 输入电压： | 2.6 V ~ 4 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 640kHz，1.2MHz |
| 电流 - 输出： | 300mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-uMAX |
Low-Noise Step-Up DC-DC Converter
Diode Selection
The output diode should be rated to handle the output
voltage and the peak switch current. Make sure that the
diode’s peak current rating is at least I PK and that its
breakdown voltage exceeds V OUT . Schottky diodes are
recommended.
Input and Output Capacitor Selection
Low-ESR capacitors are recommended for input
bypassing and output filtering. Low-ESR tantalum
capacitors are a good compromise between cost and
performance. Ceramic capacitors are also a good
choice. Avoid standard aluminum electrolytic capaci-
tors. A simple equation to estimate input and output-
capacitor values for a given voltage ripple is as follows:
COMP to GND. R COMP is chosen to set the high-fre-
quency integrator gain for fast-transient response, while
C COMP is chosen to set the integrator zero to maintain
loop stability. The second capacitor, C COMP2 , is chosen
to cancel the zero introduced by output-capacitance
ESR. For optimal performance, choose the components
using the following equations:
R COMP = (274 Ω /A 2 x VIN x VOUT x C OUT /(L x I OUT )
C COMP ? (0.36 x 10 -3 A/ Ω ) x L/V IN
C COMP2 ? (0.0036 A/ Ω ) x R ESR x L x I OUT/(VIN x VOUT)
For the ceramic output capacitor, where ESR is small,
C COMP2 is optional. Table 1 shows experimentally verified
external component values for several applications.
C ≥
0.5 × L × ?? I PK 2 ??
V RIPPLE × V OUT
The best gauge of correct loop compensation is by
inspecting the transient response of the MAX17067.
Adjust R COMP and C COMP as necessary to obtain opti-
mal transient performance.
R 1 = R 2 ? OUT ? 1 ?
C SS > 21 × 10 ? 6 × C OUT ?
where V RIPPLE is the peak-to-peak ripple voltage on the
capacitor.
Output Voltage
The MAX17067 operates with an adjustable output from
V IN to 20V. Connect a resistor voltage-divider to FB
(see the Typical Operating Circuit) from the output to
GND. Select the resistor values as follows:
? V ?
? V FB ?
where V FB , the boost-regulator feedback set point, is
1.24V. Since the input bias current into FB is typically
zero, R2 can have a value up to 100k Ω without sacrificing
accuracy. Connect the resistor-divider as close to the IC
as possible.
Loop Compensation
The voltage feedback loop needs proper compensation
to prevent excessive output ripple and poor efficiency
caused by instability. This is done by connecting a resis-
tor (R COMP ) and capacitor (C COMP ) in series from
COMP to GND, and another capacitor (C COMP2 ) from
Soft-Start Capacitor
The soft-start capacitor should be large enough that it
does not reach final value before the output has
reached regulation. Calculate C SS to be:
? V OUT 2 ? V IN × V OUT ?
?
? V IN × I INRUSH ? I OUT × V OUT ?
where:
C OUT = total output capacitance including any bypass
capacitor on the output bus
V OUT = maximum output voltage
I INRUSH = peak inrush current allowed
I OUT = maximum output current during power-up stage
V IN = minimum input voltage
The load must wait for the soft-start cycle to finish
before drawing a significant amount of load current.
The duration after which the load can begin to draw
maximum load current is:
t MAX = 2.5 x 10 5 C SS
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1706EEE+T | IC REG BOOST ADJ 0.4A 16QSOP |
| MAX17075ETG+T | IC DC-DC CONV W/CHRG PUMP 24TQFN |
| MAX17080GTL+T | IC CONTROLLER AMD SVI 40-TQFN |
| MAX17083ETG+T | IC REG BUCK ADJ 5A 24TQFN |
| MAX17085GTL+ | IC CHARGER/CTLR/LDO REG 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17068AAX/V+ | 制造商:Maxim Integrated Products 功能描述:10-CHANNEL HIGH-VOLTAGE SENSOR SMART DATA-ACQUISITION INTERF - Rail/Tube |
| MAX17069AAX+ | 制造商:Maxim Integrated Products 功能描述:10-CHANNEL HIGH-VOLTAGE SENSOR SMART DATA-ACQUISITION INTERF - Rail/Tube |
| MAX1706EEE | 功能描述:直流/直流开关转换器 1-3 Cell Step-Up w/Linear Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1706EEE+ | 功能描述:直流/直流开关转换器 1-3 Cell Step-Up w/Linear Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1706EEE+T | 功能描述:直流/直流开关转换器 1-3 Cell Step-Up w/Linear Regulator RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。