- 您现在的位置：买卖IC网 > PDF目录15514 > MAX1714BEEE+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1714BEEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 600kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
High-Speed Step-Down Controller
for Notebook Computers
DH
V BATT
Layout Procedure
1) Place the power components first, with ground termi-
nals adjacent (Q2 source, CIN-, COUT-, D1 anode). If
possible, make all these connections on the top layer
MAX1714
DL
V OUT
with wide, copper-filled areas.
2) Mount the controller IC adjacent to MOSFET Q2,
preferably on the back side opposite Q2 in order to
PGND
(GND)
OUT
R1
keep LX, PGND, and the DL gate-drive lines short and
wide. The DL gate trace must be short and wide,
measuring 10 to 20 squares (50 to 100 mils wide if the
FB
R2
AGND
(GND)
( ) ARE FOR THE MAX1714B ONLY.
Figure 9. Setting V OUT with a Resistor-Divider
where a single milliohm of excess trace resistance
causes a measurable efficiency penalty.
? LX and PGND connections to Q2 for current limiting
must be made using Kelvin sense connections to
guarantee the current-limit accuracy. With SO-8
MOSFETs, this is best done by routing power to the
MOSFETs from outside using the top copper layer,
while tying in PGND and LX inside (underneath) the
SO-8 package.
? When trade-offs in trace lengths must be made, it’s
preferable to allow the inductor charging path to be
made longer than the discharge path. For example,
it’s better to allow some extra distance between the
input capacitors and the high-side MOSFET than to
allow distance between the inductor and the low-
side MOSFET or between the inductor and the out-
put filter capacitor.
? Ensure that the OUT connection to C OUT is short and
direct. However, in some cases it may be desirable to
deliberately introduce some trace length between the
OUT inductor node and the output filter capacitor (see
the All-Ceramic-Capacitor Application section).
? Route high-speed switching nodes (BST, LX, DH, and
DL) away from sensitive analog areas (REF, FB).
? Make all pin-strap control input connections ( SKIP ,
ILIM, etc.) to AGND or V CC rather than PGND or V DD .
MOSFET is 1 inch from the controller IC).
3) Group the gate-drive components (BST diode and
capacitor, V DD bypass capacitor) together near the
controller IC.
4) Make the DC-DC controller ground connections as
shown in Figure 11. This diagram can be viewed as
having three separate ground planes: output ground,
where all the high-power components go; the PGND
plane, where the PGND pin and V DD bypass capaci-
tor go; and an analog AGND plane, where sensitive
analog components go. The analog ground plane and
PGND plane must meet only at a single point directly
beneath the IC. For the MAX1714B, this point should
be the GND pin. These two planes are then connect-
ed to the high-power output ground with a short con-
nection from V DD cap/PGND to the source of the
low-side MOSFET, Q2 (the middle of the star ground).
This point must also be very close to the output
capacitor ground terminal.
5) Connect the output power planes (V CORE and system
ground planes) directly to the output filter capacitor
positive and negative terminals with multiple vias.
Place the entire DC-DC converter circuit as close to
the CPU as is practical.
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1762EUB+ | IC REG CTRLR BUCK PWM CM 10-UMAX |
| MAX1791EUB+ | IC REG CTRLR BUCK PWM CM 10-UMAX |
| MAX775CSA+ | IC REG CTRLR INV PWM 8-SOIC |
| MAX776CSA+ | IC REG CTRLR INV PWM 8-SOIC |
| MAX774CSA+ | IC REG CTRLR INV PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1714BEEE+ | 功能描述:电流型 PWM 控制器 Step-Down Controller for Notebook RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1714BEEE+T | 功能描述:电流型 PWM 控制器 Step-Down Controller for Notebook RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1714BEEE-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1714BEEE-TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1714BEVKIT | 功能描述:电流型 PWM 控制器 Evaluation Kit for the MAX1714B RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。